print barcode in c#.net X10 Dimmer in Software

Drawing Denso QR Bar Code in Software X10 Dimmer

9
Print QR Code JIS X 0510 In None
Using Barcode maker for Software Control to generate, create QR Code 2d barcode image in Software applications.
Denso QR Bar Code Scanner In None
Using Barcode decoder for Software Control to read, scan read, scan image in Software applications.
Figure 9-20
QR Code 2d Barcode Generator In Visual C#.NET
Using Barcode generator for Visual Studio .NET Control to generate, create QR-Code image in .NET framework applications.
Creating QR In VS .NET
Using Barcode creator for ASP.NET Control to generate, create QR Code ISO/IEC18004 image in ASP.NET applications.
Wireless X10 receiver (Photo courtesy Smarthomecom)
QR Code 2d Barcode Drawer In VS .NET
Using Barcode generator for Visual Studio .NET Control to generate, create Denso QR Bar Code image in VS .NET applications.
QR Code 2d Barcode Printer In VB.NET
Using Barcode maker for Visual Studio .NET Control to generate, create QR Code JIS X 0510 image in .NET applications.
X10 Dimmer
EAN / UCC - 13 Encoder In None
Using Barcode encoder for Software Control to generate, create GTIN - 13 image in Software applications.
Encode Bar Code In None
Using Barcode creator for Software Control to generate, create barcode image in Software applications.
When the motion detector senses activity, it will send an X10 signal either via our Omni II security system, or via an X10 device This signal will be programmed for reception by our X10 dimmer switch
Generating Code-128 In None
Using Barcode creator for Software Control to generate, create Code 128 Code Set B image in Software applications.
Painting UCC - 12 In None
Using Barcode encoder for Software Control to generate, create UPC-A Supplement 5 image in Software applications.
Different X10 Outlet Options
Making Barcode In None
Using Barcode maker for Software Control to generate, create bar code image in Software applications.
Creating GTIN - 128 In None
Using Barcode printer for Software Control to generate, create EAN 128 image in Software applications.
Remember, there are a number of options for installing an X10-capable light fixture, not just the switch we re installing You can opt for a screw-in module, an inline module, or a dimmer with different functions, including two-way capabilities If you d rather pursue one of the other options, feel free to do so With the exception of the screw-in module (which is fairly self explanatory), the process for installing other X10 switches and inline modules will be somewhat similar As always, be sure to read your manufacturer s instructions before beginning
Code 2/5 Drawer In None
Using Barcode generator for Software Control to generate, create Code 2 of 5 image in Software applications.
EAN 128 Encoder In Objective-C
Using Barcode creation for iPad Control to generate, create UCC - 12 image in iPad applications.
15 MINUTES
Print Bar Code In Java
Using Barcode drawer for Eclipse BIRT Control to generate, create barcode image in BIRT reports applications.
Create Data Matrix In Java
Using Barcode printer for BIRT reports Control to generate, create ECC200 image in BIRT applications.
Before starting, set the X10 code on your switch to whatever you choose To help remember the code later (and so you don t have to pull the switch out of the wall to check), it s a good idea to jot down the code on a master list somewhere To install the X10 dimmer switch, follow these steps:
EAN-13 Supplement 5 Reader In .NET Framework
Using Barcode reader for .NET Control to read, scan read, scan image in VS .NET applications.
Barcode Reader In Visual Basic .NET
Using Barcode Control SDK for VS .NET Control to generate, create, read, scan barcode image in .NET applications.
1 Turn off the power at the circuit breaker 2 Remove the switch plate of the existing switch 3 Unscrew the mounting screws holding the switch to the gang box
Painting Barcode In VB.NET
Using Barcode printer for VS .NET Control to generate, create bar code image in .NET applications.
Barcode Generation In None
Using Barcode printer for Excel Control to generate, create barcode image in Office Excel applications.
Lighting the Smart Home
4 Once the switch is out, unscrew the terminals holding the wires into the switch, as shown in Figure 9-21 Depending on the switch that is installed, it might be easier to simply use a wire cutter to detach the switch from the wiring If you have to do this, you ll also need a wire stripper to get at the copper wire beneath the insulation
Figure 9-21
Remove the old light switch
Three-way Lighting Wiring
When you remove the switch, you should have two wires coming out of the gang box (and possibly a ground wire) If there are three, then one is likely a traveler wire for a three-way switch Most often, this third wire is yellow If you ve purchased a switch that is capable of handling three-way lighting, you ll use a wire connector to connect the traveler wire to the appropriate wire on the switch (but not yet!) If you are not using a three-way switch, cap this wire with a wire connector If your switch is wired for three-way application but there is no traveler wire, be sure to cap the lead on your switch
5 Next, you must determine which lead is the line wire Make sure no exposed wires are touching anything else and that no one is near the switch Go back to the circuit breaker and turn the breaker back on 6 Being careful not to touch any bare wire, use a voltmeter or a voltage sensor to test each wire With one wire of the voltage tester on the ground, test each remaining wire When the voltmeter or the voltage sensor detects 120V, then you ve found the line (or hot) wire Most often, this wire is black Ensure no one is near the wires, then turn the circuit breaker off again
9
When to Contact a Professional
If you don t feel comfortable testing wiring to determine which is hot and which is not, don t mess around call a professional electrician
7 Once you ve turned the power off at the circuit breaker again, connect the line wire to the line connection on the switch using a wire connector, shown in Figure 9-22
Figure 9-22
Connect the house line wire to the line wire of the switch
8 With some switches, there will be a bare copper wire This should be connected to the ground wire in the gang box 9 If your switch requires a neutral wire to be connected, make this connection with a wire connector Typically, the neutral wire will be white 10 Connect the load wire of the house to the load wire on the switch Secure it with a wire connector Most often, this wire is red The final installation will look similar to the picture in Figure 9-23 Note that the shown switch does not utilize a neutral wire and the traveler wire has been capped off
Figure 9-23
Copyright © OnBarcode.com . All rights reserved.