E l e c t r i c Ve h i c l e C o nve r s i o n in VS .NET

Printer QR Code 2d barcode in VS .NET E l e c t r i c Ve h i c l e C o nve r s i o n

E l e c t r i c Ve h i c l e C o nve r s i o n
QR Code Creation In VS .NET
Using Barcode generation for .NET framework Control to generate, create QR image in Visual Studio .NET applications.
QR Code JIS X 0510 Scanner In VS .NET
Using Barcode scanner for .NET framework Control to read, scan read, scan image in .NET applications.
Figure 10-26 Jim Har ris prototype magic box for 1987 F ord Ranger
Make Barcode In Visual Studio .NET
Using Barcode creator for .NET Control to generate, create bar code image in .NET applications.
Recognizing Barcode In .NET
Using Barcode reader for VS .NET Control to read, scan read, scan image in .NET framework applications.
Jim s and Paul s objectives were to simplify You ll see the continuous design evolution of Jim s magic box in later photographs as the conversion progressed and how Paul Little made it more advanced in his design
Printing QR Code In C#.NET
Using Barcode generator for VS .NET Control to generate, create QR Code ISO/IEC18004 image in Visual Studio .NET applications.
Encode QR Code ISO/IEC18004 In .NET Framework
Using Barcode generator for ASP.NET Control to generate, create QR Code 2d barcode image in ASP.NET applications.
Charger System
QR Code Generator In Visual Basic .NET
Using Barcode maker for .NET Control to generate, create QR Code 2d barcode image in Visual Studio .NET applications.
Generating EAN128 In Visual Studio .NET
Using Barcode creation for .NET Control to generate, create EAN / UCC - 14 image in .NET applications.
The benefits of the on-board charger are convenience and the ability to take advantage of on-the-road charging opportunities as they are presented The dual objectives in
EAN / UCC - 13 Drawer In .NET Framework
Using Barcode creator for .NET Control to generate, create European Article Number 13 image in VS .NET applications.
Generate Bar Code In Visual Studio .NET
Using Barcode encoder for Visual Studio .NET Control to generate, create barcode image in Visual Studio .NET applications.
Figure 10-27
Barcode Drawer In .NET Framework
Using Barcode creation for Visual Studio .NET Control to generate, create barcode image in .NET framework applications.
EAN 8 Generation In .NET
Using Barcode creator for Visual Studio .NET Control to generate, create EAN8 image in VS .NET applications.
Paul Little s EV P orsche magic box for components
Barcode Scanner In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
GS1-128 Drawer In Visual Basic .NET
Using Barcode creator for .NET Control to generate, create GTIN - 128 image in VS .NET applications.
Build Your Own Elec tric Vehicle
Printing Matrix 2D Barcode In Visual C#
Using Barcode creator for .NET Control to generate, create Matrix Barcode image in .NET applications.
Encode Code 128 Code Set C In None
Using Barcode encoder for Font Control to generate, create Code 128 Code Set A image in Font applications.
wiring the on-board charging system are to prevent the charging routine from becoming a shocking experience (via proper grounding), and to prevent momentary distractions from causing you to drive away while the charging cable is still attached (via a charger safety interlock) There are four main components to the charger system: Compact on-board charger Lightweight line booster (optional) Safety charging interlock AC input system In Jim s 1987 Ranger conversion, he mounted the on-board K & W BC-20 charger on the driver s side of the aluminum heat sink plate, directly above the motor in the engine compartment, as shown in Figure 10-28 (top) The K & W LB-20 line booster, required by the charger for 120-volt operation, is mounted next to the throttle potentiometer on the driver s side fender well (Figure 10-28, bottom) The preferred location for most AC input charging connections in conversion vehicles is usually the location vacated by the gas tank filler neck opening Figure 10-29 (top) shows that Jim s choice follows this pattern it s behind the original gas cap door Jim also chose to implement a male twist-lock three-prong AC charging connector, enabling him to use a standard extension cable (one end male, other end female) with the male plug on the extension cord end able to mate conveniently with the standard 120-volt AC female service outlets (Be sure to use a three-conductor extension cable with at least AWG 12 wire in it) Figure 10-29 (middle) shows an on-board female twistlock three-prong AC connector Figure 10-29 (bottom) shows that behind the gas tank filler door is not the only location; in this case, a male twist-lock three-prong AC connector has been recessed in the front bumper using a conventional outdoor AC junction wiring box Figures 11-30 and 31 show examples of how the gas tank filler area can also be used as a great charger location In this case, they are also using a threeprong connector and a Zivan NG3 charger For the charging system, you should use AWG 10 (30-amp rating) stranded insulated copper wire for both the charger-to-battery and the charger-to-AC-input receptacle connections In order to prevent you (or anyone else) from casually driving away with the extension cord attached while charging, it s a good idea to implement a charger interlock system Jim s approach is to use a relay whose coil is energized by the presence of 120 volts AC, and whose contacts are in series with the 12-volt keyswitch line When the 120-volt AC line cord is plugged in, this relay latches open and keeps the main battery pack disconnected from the controller and motor the vehicle is immobilized Other EV converters have also used the charger interlock feature to energize battery compartment fans (forced ventilation of the batteries) while charging Additional interlock possibilities include: sensors that inhibit drive-away when the fault conditions of engine compartment hood open, battery compartment hood open, or AC charging connector access door open are detected; and sensors that inhibit the charging function during fault conditions such as engine or battery compartment hood open (because you don t want outsiders prying when charging currents and battery gases are present) You might consider any of these options In order to prevent you (or anyone else) from getting shocked when touching your EV s body while it s charging, the body and frame should be grounded to the AC neutral line (the third prong of the connector with the green wire leading to it) This
GS1-128 Generation In Java
Using Barcode generator for Java Control to generate, create EAN / UCC - 14 image in Java applications.
Data Matrix ECC200 Creator In None
Using Barcode printer for Font Control to generate, create ECC200 image in Font applications.
10:
Decode Bar Code In Java
Using Barcode Control SDK for BIRT reports Control to generate, create, read, scan barcode image in BIRT reports applications.
Bar Code Generation In None
Using Barcode generator for Word Control to generate, create barcode image in Office Word applications.
Copyright © OnBarcode.com . All rights reserved.