Five in Software

Printer Code 39 Full ASCII in Software Five

Five
Drawing Code39 In None
Using Barcode encoder for Software Control to generate, create Code 39 Full ASCII image in Software applications.
USS Code 39 Recognizer In None
Using Barcode recognizer for Software Control to read, scan read, scan image in Software applications.
As with the mechanical contractor, the plumbing contractor s objectives are to prefabricate the plumbing assemblies and determine the location of inserts and hangers by using the 3D model Therefore, the plumbing contractor should model all his or her plumbing fixtures, graded cast iron pipelines, underground storm and sewer pipes, all major waste and vent lines, cold and hot water piping, seismic details, all boiler and other equipment, and specialty piping (such as medical gas piping) and specialty equipment This detail allows the plumbing contractor to prefabricate materials in the shop environment For example, Fig 515 shows a screenshot of the 3D model with the plumbing gravity lines, fixtures, hot and cold water pipes for the first-ffloor SE quadrant of the Camino MOB project Sprinkler Model The fire protection contractor should model the mains and branches, the drop pipes, and the exact location of drops in the ceiling This allows the contractor to lay out the mains and branches, prefabricate and also install inserts before the deck is poured For example, Fig 516 shows a snapshot of the 3D sprinkler model for one of the quadrants of the Camino MOB with its mains, branches, and sprinkler drops Levels of Detail in Architectural, Structural, and MEP/FP Models and Potential Uses and Benefits Two of the key questions when applying VDC methodologies to the 3D MEP/FP coordination process are, What level of detail should be included in the models and What uses and benefits can a team obtain from the models Table 511 summarizes answers to these questions
Code-39 Creation In Visual C#.NET
Using Barcode generation for VS .NET Control to generate, create Code 3 of 9 image in .NET framework applications.
Code 39 Extended Drawer In VS .NET
Using Barcode generator for ASP.NET Control to generate, create Code 3/9 image in ASP.NET applications.
Figure 515 Snapshot of the plumbing model of first-floor SE quadrant of Camino MOB The snapshot shows the waste and vents and the plumbing fixture locations (in green), the cold water supply (in blue), and hot water lines (in red) (Image courtesy of DPR Construction, Inc, California) See also color insert
Creating Code39 In Visual Studio .NET
Using Barcode maker for .NET framework Control to generate, create USS Code 39 image in VS .NET applications.
Encode ANSI/AIM Code 39 In VB.NET
Using Barcode printer for .NET framework Control to generate, create Code 39 Extended image in .NET applications.
Case Studies
Making Barcode In None
Using Barcode encoder for Software Control to generate, create bar code image in Software applications.
Universal Product Code Version A Drawer In None
Using Barcode encoder for Software Control to generate, create UPC A image in Software applications.
Figure 516 Snapshot of the 3D sprinkler model of first-floor SE quadrant of the Camino MOB The screenshot shows the mains and branches and the sprinkler drops (Image courtesy of DPR Construction, Inc, California)
Generate EAN / UCC - 14 In None
Using Barcode creation for Software Control to generate, create USS-128 image in Software applications.
Generating Barcode In None
Using Barcode generation for Software Control to generate, create bar code image in Software applications.
As indicated, there is a definite tradeoff between the levels of detail in the model and the benefits it provides in the coordination process As a result, teams should identify what benefits they want out of the modeling and coordination process before deciding what level of details the models should include Managing the Coordination Process Getting the Technical Logistics Right Technical logistics plays an important part in the coordination process It is likely that many models will be used on the project and each subcontractor will create her or his own model Team members should agree on some basic rules at the outset of the project, so the sharing of electronic models is efficient and benefits the whole team The issues that the project team should address include the following:
DataMatrix Encoder In None
Using Barcode drawer for Software Control to generate, create Data Matrix 2d barcode image in Software applications.
Code 128A Drawer In None
Using Barcode printer for Software Control to generate, create Code 128 image in Software applications.
Drawings are accompanied by standard word documents describing revisions therein Drawings are posted to a project website, ftp site, or a document collaboration site determined by the team which includes the GC, subcontractors, owner, and A/E team The collaboration site provides secure and remote access to all the model files A clear file path structure is set up on the server to organize the model files and other relevant documents Everyone works from and posts to the same server The server is backed up every night Borders and title blocks are not transmitted with the drawings Insertion points for all drawings are based on the 0,0,0 insertion point established in the architectural drawings Anything not intended to be seen in the drawing is erased prior to file transfer
Create USS-93 In None
Using Barcode drawer for Software Control to generate, create Code 9/3 image in Software applications.
ECC200 Decoder In None
Using Barcode decoder for Software Control to read, scan read, scan image in Software applications.
Five
Paint Bar Code In VS .NET
Using Barcode encoder for VS .NET Control to generate, create barcode image in .NET applications.
Drawing ECC200 In VB.NET
Using Barcode creator for Visual Studio .NET Control to generate, create Data Matrix ECC200 image in VS .NET applications.
Table 51 1 Level of detail in the 3D model and potential uses and benefits for each of the disciplines
Code 39 Full ASCII Maker In Objective-C
Using Barcode encoder for iPad Control to generate, create Code 39 image in iPad applications.
Generating UPC Symbol In Java
Using Barcode drawer for Java Control to generate, create UPC-A image in Java applications.
Printing GTIN - 128 In .NET Framework
Using Barcode encoder for .NET Control to generate, create UCC - 12 image in .NET framework applications.
Create GTIN - 13 In None
Using Barcode generation for Online Control to generate, create EAN13 image in Online applications.
Copyright © OnBarcode.com . All rights reserved.