qr code c# sample 16: Initial Router Con guration in Objective-C

Generator QR Code in Objective-C 16: Initial Router Con guration

16: Initial Router Con guration
Print Denso QR Bar Code In Objective-C
Using Barcode generation for iPhone Control to generate, create QR Code image in iPhone applications.
Barcode Generation In Objective-C
Using Barcode maker for iPhone Control to generate, create barcode image in iPhone applications.
Enter enable secret: dealgroup1 The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images Enter enable password: dealgroup2 The virtual terminal password is used to protect access to the router over a network interface Enter virtual terminal password: cisco Configure SNMP Network Management [no]: Configure LAT [yes]: no Configure AppleTalk [no]: Configure DECnet [no]: Configure IP [yes]: Configure IGRP routing [yes]: no Configure RIP routing [no]: Configuring interface parameters: Do you want to configure Ethernet0 interface [no]: yes Configure IP on this interface [no]: yes IP address for this interface: 1721611 Subnet mask for this interface [25525500] : 2552552550 Class B network is 1721600, 24 subnet bits; mask is /24 Do you want to configure Serial0 interface [no]: The following configuration command script was created: hostname Router enable secret 5 $1$/CCk$4r7zDwDNeqkxFOkJxC3G0 enable password dealgroup2 line vty 0 4 password cisco end [0] Go to the IOS command prompt without saving this config [1] Return back to the setup without saving this config [2] Save this configuration to nvram and exit Enter your selection [2]: 2
QR Code JIS X 0510 Encoder In C#
Using Barcode printer for VS .NET Control to generate, create Denso QR Bar Code image in VS .NET applications.
Generating QR Code 2d Barcode In .NET Framework
Using Barcode generator for ASP.NET Control to generate, create QR-Code image in ASP.NET applications.
Router Bootup Process
QR Code ISO/IEC18004 Printer In .NET Framework
Using Barcode creator for Visual Studio .NET Control to generate, create QR-Code image in .NET framework applications.
Create QR Code 2d Barcode In Visual Basic .NET
Using Barcode encoder for VS .NET Control to generate, create Quick Response Code image in Visual Studio .NET applications.
Information included in brackets ([]) are default values if you press ENTER, the value in the brackets is used One problem with the script is that if you make a mistake, you can t go back to the preceding question Instead, you must use the CTRL-C break sequence to abort the script and start over The following sections break down the different components of the script The questions that the script asks you might differ from router to router, depending on the hardware model, the interfaces installed in it, and the software running on it
Draw UPCA In Objective-C
Using Barcode printer for iPhone Control to generate, create UPC Code image in iPhone applications.
Code 128 Creation In Objective-C
Using Barcode printer for iPhone Control to generate, create USS Code 128 image in iPhone applications.
Status and Global Configuration Information
Encoding Barcode In Objective-C
Using Barcode generation for iPhone Control to generate, create bar code image in iPhone applications.
Printing EAN / UCC - 14 In Objective-C
Using Barcode generation for iPhone Control to generate, create EAN / UCC - 14 image in iPhone applications.
At the beginning of the script, you are asked whether or not you want to continue If you answer yes or y, the script will continue; otherwise, if you answer no or n, the script is aborted and you are returned to Privilege EXEC mode The second thing that you are asked is if you want to see the status of the router s interfaces If you answer yes, you ll see all of the interfaces on the router, the interfaces IP addresses, and the status of the interfaces After the status information, you are taken into the actual configuration The first part of the configuration deals with all configuration information for the router except for the interfaces, which is the second part In this part of the configuration, you are asked for things like the Privilege EXEC password, VTY password (telnet and SSH), which network protocols you want to activate globally, and other global configuration information Note that you are prompted for two Privilege EXEC passwords in the script: enable secret and enable password Even though you would normally configure only one, the script requires you to enter both and also requires that both passwords be different
Paint Code 3/9 In Objective-C
Using Barcode printer for iPhone Control to generate, create Code 39 image in iPhone applications.
Painting UPC - 13 In Objective-C
Using Barcode generator for iPhone Control to generate, create EAN13 image in iPhone applications.
Protocol and Interface Configuration Information
UPC-E Supplement 5 Generation In Objective-C
Using Barcode generation for iPhone Control to generate, create UCC - 12 image in iPhone applications.
Bar Code Decoder In Java
Using Barcode Control SDK for Java Control to generate, create, read, scan barcode image in Java applications.
After configuring the global information for the router, you are then led through questions about which interfaces you want to use and how they should be configured The script is smart enough to ask only configuration questions based on how you answered the global questions As an example, if you activate IP, the script asks you for each activated interface, if you want the interface to process IP, and, if yes, the IP addressing information for the interface
Print UPC-A In None
Using Barcode generation for Office Excel Control to generate, create UPC-A Supplement 5 image in Excel applications.
Code 39 Full ASCII Recognizer In Java
Using Barcode decoder for Java Control to read, scan read, scan image in Java applications.
16: Initial Router Con guration
Encoding ECC200 In None
Using Barcode printer for Online Control to generate, create DataMatrix image in Online applications.
Code 3/9 Creation In None
Using Barcode generation for Microsoft Word Control to generate, create Code 39 Full ASCII image in Office Word applications.
Exiting Setup Mode
Encoding Barcode In Objective-C
Using Barcode generation for iPad Control to generate, create barcode image in iPad applications.
Drawing Data Matrix 2d Barcode In None
Using Barcode encoder for Microsoft Word Control to generate, create DataMatrix image in Office Word applications.
After you answer all of the script s configuration questions, you are shown the router configuration the script created using your answers to the script s questions Note that the IOS hasn t yet activated the configuration file Examine the configuration closely and then make one of the three choices shown in Table 16-2 Also, if you enter 1 as your option, when the script starts over again, the information that you previously entered appears in brackets and will be the default values when you press the ENTER key on an empty line
Copyright © OnBarcode.com . All rights reserved.