qr code generator c# tutorial 26: Frame Relay in Objective-C

Generator Denso QR Bar Code in Objective-C 26: Frame Relay

26: Frame Relay
QR Printer In Objective-C
Using Barcode maker for iPhone Control to generate, create QR Code image in iPhone applications.
Bar Code Drawer In Objective-C
Using Barcode creation for iPhone Control to generate, create bar code image in iPhone applications.
At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-1 Execute the following: configure terminal, interface serial0, shutdown, and end Use the show interfaces command to check the status of the interfaces At this point, only the fa0/0 interface on the 2600-1 should be enabled 2 On the 2600-2 router, disable serial0 this is the dedicated point-topoint connection and you ll be setting up Frame Relay At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-2 Execute the following: configure terminal, interface serial0, shutdown, and end Use the show interfaces command to check the status of the interfaces At this point, only the fa0/0 interface on the 2600-2 should be enabled 3 Enable Frame Relay on the 2600-1 Enable the serial1 interface Use the Cisco frame type for Frame Relay Set the LMI type to ITU-T Assign the IP address At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-1 Enable the Frame Relay interface: configure terminal, interface serial1, and no shutdown Set the encapsulation and frame type: encapsulation frame-relay Set the LMI type: frame-relay lmi-type q933a Assign the IP address on the interface: ip address 192168101 2552552550 Exit Configuration mode: end 4 Verify the operational state of the interface as well as LMI Use the show interfaces command to verify that the interface is up and up and that LMI is functioning Use the show frame-relay lmi command to make sure the router is sending and receiving LMI information 5 Enable Frame Relay on the 2600-2 Enable the serial1 interface Use the Cisco frame type for Frame Relay Set the LMI type to ITU-T Assign the IP address Verify the operation of LMI At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-2 From the 2600-2 router, enable the interface: configure terminal, interface serial1, and no shutdown Set the encapsulation and frame type: encapsulation frame-relay Set the LMI type: frame-relay lmi-type q933a Assign the IP address on the interface: ip address 192168102 2552552550 Exit Configuration mode: end
Denso QR Bar Code Encoder In C#
Using Barcode printer for VS .NET Control to generate, create QR Code ISO/IEC18004 image in Visual Studio .NET applications.
QR Code Creator In .NET Framework
Using Barcode printer for ASP.NET Control to generate, create QR Code image in ASP.NET applications.
Frame Relay Con guration
Printing Denso QR Bar Code In VS .NET
Using Barcode creator for VS .NET Control to generate, create QR image in .NET applications.
Painting Quick Response Code In VB.NET
Using Barcode creator for .NET framework Control to generate, create QR Code ISO/IEC18004 image in .NET applications.
6 Verify the operational state of the interface as well as LMI Use the show interfaces command to verify that the interface is up and up and that LMI is functioning Use the show frame-relay lmi command to make sure the router is sending and receiving LMI information 7 Verify your PVC configuration and status on the 2600-2 View the resolution entry: show frame-relay map View the PVC: show frame-relay pvc The status of the VC should be ACTIVE 8 Verify your PVC configuration and status on the 2600-1 At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-1 View the resolution entry: show frame-relay map View the PVC: show frame-relay pvc The status of the VC should be ACTIVE 9 Ping the 2600-2 s Frame Relay interface address Test connectivity: ping 192168102 The ping should be successful 10 On the 2600-1 router, set up a static route to the 2600-2 s remote network View the routing table At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-1 On the 2600-1, set up the static route to reach 19216830/24: configure terminal and ip route 19216830 2552552550 192168102 Exit Configuration mode: end View the routing table and look for the static route: show ip route 11 On the 2600-2 router, set up a static route to the 2600-1 s remote network View the routing table At the top of the simulator in the menu bar, click the eRouters icon and choose 2600-2 On the 2600-2, set up the static route to reach 19216830/24: configure terminal and ip route 19216810 2552552550 192168101 Exit Configuration mode: end View the routing table and look for the static route: show ip route 12 From Host-1, test the connection to Host-3 At the top of the simulator in the menu bar, click the eStations icon and choose Host-1 On Host-1, ping Host-3: ping 192168310 The ping should be successful You should now be more familiar with setting up a basic manually resolved Frame Relay connection to a remote site
Generating GS1-128 In Objective-C
Using Barcode generator for iPhone Control to generate, create EAN / UCC - 13 image in iPhone applications.
Drawing EAN13 In Objective-C
Using Barcode creation for iPhone Control to generate, create European Article Number 13 image in iPhone applications.
Drawing UPCA In Objective-C
Using Barcode printer for iPhone Control to generate, create UPC-A Supplement 5 image in iPhone applications.
Print Bar Code In Objective-C
Using Barcode drawer for iPhone Control to generate, create bar code image in iPhone applications.
Creating Bar Code In Objective-C
Using Barcode generator for iPhone Control to generate, create barcode image in iPhone applications.
Barcode Creation In Objective-C
Using Barcode generation for iPhone Control to generate, create bar code image in iPhone applications.
Generating EAN-8 Supplement 5 Add-On In Objective-C
Using Barcode generator for iPhone Control to generate, create EAN8 image in iPhone applications.
UPC Code Decoder In Visual Basic .NET
Using Barcode scanner for .NET framework Control to read, scan read, scan image in .NET framework applications.
Data Matrix 2d Barcode Maker In VB.NET
Using Barcode generator for Visual Studio .NET Control to generate, create DataMatrix image in VS .NET applications.
Bar Code Drawer In VS .NET
Using Barcode generation for Reporting Service Control to generate, create bar code image in Reporting Service applications.
Code-128 Recognizer In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
Making Data Matrix 2d Barcode In None
Using Barcode creator for Microsoft Word Control to generate, create ECC200 image in Microsoft Word applications.
Printing UCC-128 In Visual Studio .NET
Using Barcode encoder for ASP.NET Control to generate, create EAN / UCC - 13 image in ASP.NET applications.
Code 39 Generator In Visual Basic .NET
Using Barcode creator for Visual Studio .NET Control to generate, create Code39 image in .NET applications.
Copyright © OnBarcode.com . All rights reserved.