barcode in microsoft excel 2010 Connectivity Protocols in Software

Draw DataMatrix in Software Connectivity Protocols

Connectivity Protocols
Making Data Matrix ECC200 In None
Using Barcode printer for Software Control to generate, create Data Matrix ECC200 image in Software applications.
Data Matrix 2d Barcode Reader In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
Device connections are listed in the bottom-left window of the ConfigMaker main interface After selecting a connection type there, click in the Network Diagram on the two devices to be connected
DataMatrix Maker In C#
Using Barcode encoder for Visual Studio .NET Control to generate, create Data Matrix ECC200 image in .NET framework applications.
Creating Data Matrix In Visual Studio .NET
Using Barcode creation for ASP.NET Control to generate, create Data Matrix image in ASP.NET applications.
Cisco ConfigMaker then prompts you for specific information when a connection type is chosen Table 5-3 outlines the information required to configure each particular connection type Table 5-3: Information to Configure for Various Connections
ECC200 Drawer In .NET Framework
Using Barcode encoder for VS .NET Control to generate, create Data Matrix image in .NET applications.
Data Matrix Generator In VB.NET
Using Barcode creator for VS .NET Control to generate, create Data Matrix image in .NET framework applications.
Type
Code39 Creator In None
Using Barcode printer for Software Control to generate, create Code 3 of 9 image in Software applications.
Bar Code Generation In None
Using Barcode maker for Software Control to generate, create bar code image in Software applications.
Ethernet
Making Code 128 Code Set B In None
Using Barcode printer for Software Control to generate, create Code 128 image in Software applications.
European Article Number 13 Generator In None
Using Barcode encoder for Software Control to generate, create European Article Number 13 image in Software applications.
HDLC
GS1-128 Creator In None
Using Barcode printer for Software Control to generate, create EAN 128 image in Software applications.
Barcode Generation In None
Using Barcode creator for Software Control to generate, create bar code image in Software applications.
Frame Relay
UPC Case Code Generation In None
Using Barcode printer for Software Control to generate, create EAN / UCC - 14 image in Software applications.
Barcode Creation In Java
Using Barcode drawer for Java Control to generate, create bar code image in Java applications.
ISDN
Scanning Barcode In None
Using Barcode recognizer for Software Control to read, scan read, scan image in Software applications.
Paint Bar Code In None
Using Barcode maker for Font Control to generate, create barcode image in Font applications.
Voice
Encode USS Code 128 In Objective-C
Using Barcode printer for iPhone Control to generate, create Code 128A image in iPhone applications.
Scanning Bar Code In VB.NET
Using Barcode reader for VS .NET Control to read, scan read, scan image in Visual Studio .NET applications.
Port interface/number IP address Network bits/subnet mask IPX number IPX frame type Ethernet port for IP unnumbered NAT WAN internal IP address Global address pool Static address of local host, global address, IP service Easy IP LMI type DLCI (source and destination) Option to back up Group name Either ISDN PRI interfaces (x23) T1 frame type Dial-in PC pool address Usernames and passwords of each user or ISDN BRI interfaces (x2) Services provider identifiers (SPID) Corporate network phone number Chap password Remote router name Phone number (all digits) External mapping to telephone numbers
Making Code 128 Code Set B In Visual C#
Using Barcode printer for .NET Control to generate, create Code-128 image in .NET applications.
Making EAN13 In None
Using Barcode creation for Font Control to generate, create GS1 - 13 image in Font applications.
Cisco ConfigMaker supports Information Protocol Version 2 (RIPv2) and Enhanced IGRP All devices in the network must use the same routing protocol Since EIGRP does not work over ISDN and Asynchronous connections they will use snapshot routing In addition, EIGRP does not work over LAN connections when using native IPX and AppleTalk protocols in ConfigMaker Instead, LAN connections will use RIP for IPX and AppleTalk protocols even though the rest of the network will use EIGRP IP, IPX, and AppleTalk are the routed protocols supported by ConfigMaker assuming all your network devices support these protocols The IP protocol is set by default Set your routed protocols in the initial ConfigMaker Device or AutoDetect Device Wizards If you want to change the routed protocol parameters of existing devices, right-click the device and select Device Properties Then click the Protocols tab (Figure 5-6) By Selecting different routed protocols here and clicking Apply, you apply those parameters only to the devices selected in the Network Diagram window of the main ConfigMaker interface
Figure 5-6: Changing routed protocols on specific devices When you add routed protocols to network devices, you may need to run the connection wizards again to establish the connections To start the wizard, double-click the connection between the devices in which protocols were added in the Network Diagram window After completing the connection wizard, deliver the altered configurations to the devices, using the Deliver Configuration Wizard ConfigMaker cross-checks the common protocol between locations when connections are enabled, thereby preventing incompatible configurations
Installing and Configuring ConfigMaker
Installation of ConfigMaker is straightforward and should be uneventful The application takes up just under 16MB when installed on a clean machine and even less when installed on a machine that already has the necessary shared DLLs and controls You don't have to reboot after installation
Machine/Implementation Requirements
Following are the minimum requirements for installing and using Cisco ConfigMaker 24: Pentium-class or 80486-based computer with 16MB of RAM 20MB hard disk space SVGA monitor at 800 600 pixel display with at least 256 colors CD-ROM drive Windows 9x or Windows NT 40 SP3
Cisco IOS 112 or later on your routers In addition, the following capabilities are recommended: Internet connection on the PC running ConfigMaker Netscape Navigator 30 or later or Microsoft Internet Explorer 30 or later
Using ConfigMaker
The ConfigMaker interface has a task list in the right-hand side of the main window, which defines the steps you need to take to configure and draw your network This task list is helpful when using ConfigMaker for the first time
Drawing the Network Devices
You can draw your network by adding devices and connections manually to the Network Diagram window, from the Devices and Connection lists on the left side of the main interface Or you can use the AutoDetect Device Wizard To add a device manually, click a device in the Devices list and drag it to the Network Diagram window The Device Wizard will lead you through a series of dialog boxes, asking you for the configuration parameters The configuration parameters are dependent on the type of device selected, but they may include things such as user and privilege passwords, routed protocols, and the cards installed (assuming the device is modular) Specific information related to the interface configurations (including IP addresses) is defined when you establish a connection between two devices The AutoDetect Device Wizard can identify supported devices by a connection to a device through a console port or through a direct network connection During device detection, if a Cisco modular router is found, the wizard also identifies the network modules, WAN Interface Cards (WICs), and Voice Interface Cards (VICs) This wizard helps you detect devices on your network and reports important information about them, such as the type of installed NIC and the IOS software version number
Copyright © OnBarcode.com . All rights reserved.