using barcode in excel 2010 The Setup Program/Process in Software

Printing Data Matrix ECC200 in Software The Setup Program/Process

The Setup Program/Process
DataMatrix Maker In None
Using Barcode printer for Software Control to generate, create Data Matrix 2d barcode image in Software applications.
ECC200 Recognizer In None
Using Barcode decoder for Software Control to read, scan read, scan image in Software applications.
As with other Cisco network devices, your initial means of connecting to a switch is through the console port After this initial connection and configuration, you have three options for connecting to a switch: via the console port, via Telnet, and via the browser-style Visual Switch Manager software The initial connection, and configuration through the console port and with Telnet, are discussed in the following paragraphs Configuration using Visual Switch Manager software is discussed in more detail in a later section
ECC200 Encoder In C#
Using Barcode encoder for Visual Studio .NET Control to generate, create ECC200 image in .NET applications.
Printing Data Matrix 2d Barcode In VS .NET
Using Barcode maker for ASP.NET Control to generate, create DataMatrix image in ASP.NET applications.
Connecting via the Console
Drawing Data Matrix 2d Barcode In .NET Framework
Using Barcode maker for .NET framework Control to generate, create ECC200 image in .NET applications.
Data Matrix 2d Barcode Generator In Visual Basic .NET
Using Barcode maker for .NET Control to generate, create Data Matrix image in Visual Studio .NET applications.
Included with the purchase of a switch is a rollover cable Connect one side of this RJ45 cable into the console port The other side goes into an adapter, either an RJ-45 to DB-9 female DTE adapter, or an RJ-45 to DB-25 adapter Your terminal emulation software needs to communicate with the switch using hardware flow control The terminal type should be set to VT100 Several terminal software applications are available, including the Hyperterminal program that is included with Windows 9x and NT 40 Hyperterminal and most of the other terminal programs provide an easy path to the console port The following configuration supports a serial connection to the switch's console port: Baud rate Data bits Stop bits Parity Flow control Terminal type 9600 8 1 None None VT100
Generate Code 128A In None
Using Barcode creator for Software Control to generate, create Code 128 Code Set C image in Software applications.
Bar Code Maker In None
Using Barcode printer for Software Control to generate, create bar code image in Software applications.
Configure the terminal emulator using these parameters and then, if you haven't already done so, power up the switch Press Enter a couple of times until you see a prompt The first time you boot up the switch, you'll be prompted for IP information Although this information is not required for the switch to work, it is necessary to allow connectivity through a Telnet session or Visual Switch Manager software The initial IP information can only be configured using the console port This is also a good time to set your passwords for the switch, and change the default SNMP community strings (even though these configurations can be done through a Telnet session or Visual Switch Manager) If you decide against using the software prompts during the initial powering of the switch or if you want to change these configurations, you can use the CLI The following procedure describes how to change the IP information for the 2900 Series switches using the CLI (this process is similar across the majority of switches):
Make GS1-128 In None
Using Barcode generation for Software Control to generate, create EAN128 image in Software applications.
Bar Code Drawer In None
Using Barcode generator for Software Control to generate, create barcode image in Software applications.
1Enter privileged EXEC mode: Switch>enable 2Enter global configuration mode: Switch#configuration terminal 3Enter the interface configuration mode and specify the interface to which the IP information is being assigned: Switch(config)#interface VLAN1 VLAN1 is by default the switch's interface 4Assign the IP address and subnet mask: Switch(config-if)#ip address ip_address subnet_mask 5Define the IP address of the default router: Switch(config-if)#ip default-gateway ip_address In addition to providing IP information, you'll need to enable Telnet on the switch in order to connect to the switch through a Telnet session Here is one way to enable Telnet connectivity and a password for Telnet authorization: 1Enter privileged EXEC mode: Switch>enable 2Enter global configuration mode: Switch#configuration terminal 3Enter the interface configuration mode for the Telnet session: Interface switch(config)#line vty 0 4 where 0 and 4 indicate a range of 0 4 (total of five) Telnet sessions allowed at one time 4Enter a password Switch(config)#password password
Code 39 Full ASCII Drawer In None
Using Barcode printer for Software Control to generate, create USS Code 39 image in Software applications.
UPC Code Printer In None
Using Barcode encoder for Software Control to generate, create UCC - 12 image in Software applications.
Telnet
MSI Plessey Drawer In None
Using Barcode maker for Software Control to generate, create MSI Plessey image in Software applications.
Barcode Creation In Java
Using Barcode generation for Android Control to generate, create barcode image in Android applications.
A connection through Telnet is useful for remote administration of network devices Once you have the IP address assigned and the password configured, launch the Telnet application Windows NT, Windows 9x, and Windows 2000 include a Telnet application that will do the trick Enter the IP address of the switch you would like to connect to You will then be prompted for a password Once it's authenticated, you'll be at the switch's command line interface Cisco's IOS command line interface (CLI) is generally referred to as an EXEC session There are two levels in an EXEC session: user mode (denoted by the > prompt) and privileged mode (denoted by the # prompt) The user level is obviously very limited, and privileged mode gives you the keys to the kingdom Luckily, both levels can be password protected Changing the default password should be one of your first configuration changes TELNET CONNECTION ISSUES Once you have connected to a switch using Telnet and entered the user-level password, the CLI is similar to that for a Cisco router One thing that might be a little confusing, though: For a router, configurations can be assigned to a router's interface For a switch, configurations can be assigned to a VLAN or to a switch's interface, depending on what type of configuration is being applied
Drawing UCC - 12 In .NET
Using Barcode creator for ASP.NET Control to generate, create UPC-A Supplement 5 image in ASP.NET applications.
Code 128 Code Set A Maker In None
Using Barcode drawer for Online Control to generate, create USS Code 128 image in Online applications.
For example, here is the int command to configure a particular interface for a router: Router(config)#int Ethernet0 Router(config-if)# However, in a switch, the configurations can be assigned to VLANs or interfaces, so you'd type one of these int commands: Switch(config)#int VLAN1 Switch(config-if)# or Switch(config)#int Fast Ethernet1 Switch(config-if)# Notice that Cisco returns the prompt Switch(config-if)# instead of Switch(config-VLAN)# which it should have returned in the case of assigning configurations to a VLAN The if prompt in a router refers to an interface, but here it refers to a VLAN thus there can be confusion about whether your configurations are being assigned to the switch interface or a VLAN of the switch Make sure you know whether the configurations should be applied to the interface or to the VLAN before using sthe int command When connecting to a switch via Telnet, another consideration concerns the login When you log into a switch, you are in the user mode To access the privileged mode, type enable at the > prompt The CLI will then prompt you for the enable password Even though the switch does not echo either the user or privileged password, Telnet will send the password in clear text across your network, which is a security concern
Reading GS1 - 13 In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
Barcode Generator In None
Using Barcode generator for Font Control to generate, create bar code image in Font applications.
Bar Code Reader In Visual Basic .NET
Using Barcode recognizer for VS .NET Control to read, scan read, scan image in VS .NET applications.
Bar Code Printer In C#.NET
Using Barcode drawer for VS .NET Control to generate, create barcode image in Visual Studio .NET applications.
Copyright © OnBarcode.com . All rights reserved.