code 128 excel font download End with CNTL/Z in Objective-C

Encoder PDF-417 2d barcode in Objective-C End with CNTL/Z

End with CNTL/Z
Bar Code Drawer In Objective-C
Using Barcode generation for iPhone Control to generate, create barcode image in iPhone applications.
Encode PDF-417 2d Barcode In Visual C#.NET
Using Barcode printer for .NET framework Control to generate, create PDF417 image in Visual Studio .NET applications.
Note You may have noticed that the switch took some time to synchronize with the NTP server In some cases, it may take up to 30 minutes to achieve synchronization As discussed at the beginning of the chapter, setting the location and administrative contact are useful in a large organization that has many of the same switches, but it is generally unnecessary in smaller organizations To set the administrative contact, use the snmp-server contact command, as shown in this example:
Drawing PDF417 In .NET Framework
Using Barcode printer for ASP.NET Control to generate, create PDF-417 2d barcode image in ASP.NET applications.
PDF-417 2d Barcode Drawer In VS .NET
Using Barcode generation for Visual Studio .NET Control to generate, create PDF 417 image in VS .NET applications.
cat1924A(config)#snmp-server contact John Doe
Create PDF417 In Visual Basic .NET
Using Barcode creation for .NET Control to generate, create PDF-417 2d barcode image in .NET framework applications.
Bar Code Encoder In Objective-C
Using Barcode generation for iPhone Control to generate, create barcode image in iPhone applications.
To set the location for the switch, use the snmp-server location command, as shown next:
Make European Article Number 13 In Objective-C
Using Barcode creator for iPhone Control to generate, create GTIN - 13 image in iPhone applications.
Drawing Bar Code In Objective-C
Using Barcode maker for iPhone Control to generate, create bar code image in iPhone applications.
cat1924A(config)#snmp-server location Corp HQ Closet 5
Create GTIN - 128 In Objective-C
Using Barcode drawer for iPhone Control to generate, create GS1 128 image in iPhone applications.
Code 128 Code Set C Encoder In Objective-C
Using Barcode generation for iPhone Control to generate, create Code 128 image in iPhone applications.
When finished, the show snmp contact and show snmp location commands should display your settings, like so:
Code 39 Extended Creator In Objective-C
Using Barcode encoder for iPhone Control to generate, create Code-39 image in iPhone applications.
Barcode Creation In Objective-C
Using Barcode creator for iPhone Control to generate, create bar code image in iPhone applications.
cat1924A#show snmp contact John Doe cat1924A#show snmp location Corp HQ Closet 5 cat1924A#
Drawing EAN8 In Objective-C
Using Barcode creation for iPhone Control to generate, create EAN8 image in iPhone applications.
Drawing UPC-A Supplement 2 In Java
Using Barcode generator for BIRT reports Control to generate, create UPC A image in BIRT applications.
CatOS Configuration
Code-39 Reader In .NET Framework
Using Barcode scanner for Visual Studio .NET Control to read, scan read, scan image in .NET applications.
Printing UPC Symbol In Visual Basic .NET
Using Barcode creator for Visual Studio .NET Control to generate, create GS1 - 12 image in .NET framework applications.
To configure the general system information on a CatOS-based switch, the commands are a bit different First, when you boot the switch, you will be greeted with a simple prompt, like this:
Code128 Maker In None
Using Barcode maker for Software Control to generate, create Code128 image in Software applications.
Code 3/9 Generation In .NET Framework
Using Barcode printer for .NET Control to generate, create ANSI/AIM Code 39 image in .NET applications.
Console>
Code 39 Extended Creation In .NET
Using Barcode generation for ASP.NET Control to generate, create Code 39 Full ASCII image in ASP.NET applications.
Recognizing Code 128B In .NET Framework
Using Barcode reader for Visual Studio .NET Control to read, scan read, scan image in VS .NET applications.
You need to type enable to set switch parameters Because no default enable password is set, the switch simply enters into enable mode with no further typing required, as shown here:
Console enable Console (enable)
To set the name on a CatOS switch, use the set system name command To set the IP address for the in-band (Ethernet) management interface, use the set interface sc0 command Both of these are shown next:
5500A (enable) set system name Cat5K System name set Cat5K (enable) set interface sc0 1011254 2552552550 Interface sc0 IP address and netmask set Cat5K (enable) show interface sl0: flags=51<UP,POINTOPOINT,RUNNING> slip 0000 dest 0000 sc0: flags=63<UP,BROADCAST,RUNNING> vlan 1 inet 1011254 netmask 2552552550 broadcast 1011255 Cat5K (enable)
You can set the date and time on a CatOS switch either manually or by using NTP, like with the standard IOS switches To use NTP, issue the set ntp server command To set the time manually, use the set time command Both of these commands are shown in the following example:
Cat5K (enable) set ntp server 10111 NTP server 10111 added Cat5K (enable) show ntp Current time: Tue Jul 31 2001, 02:42:25 Timezone: '', offset from UTC is 0 hours Summertime: '', disabled Last NTP update: Broadcast client mode: disabled Broadcast delay: 3000 microseconds Client mode: disabled Authentication: disabled NTP-Server ---------------------------------------10111 Server Key ----------
Key Number Mode -----------------Cat5K (enable) set time wednesday 8/1/2001 14:44:00 Wed Aug 1 2001, 14:44:00 Cat5K (enable) show time Wed Aug 1 2001, 14:44:06 Cat5K (enable)
Finally, to set the contact and location information for the switch, use the set system contact command and the set system location command You can then view this information with the show system command, like so:
Cat5K (enable) set system contact John Doe System contact set Cat5K (enable) set system location Corp HQ Closet 5 System location set Cat5K (enable) show system PS1-Status PS2-Status
---------- ---------ok ok Fan-Status Temp-Alarm Sys-Status Uptime d,h:m:s Logout ---------- ---------- ---------- -------------- --------ok off ok 8,19:42:30 none PS1-Type PS2-Type ------------ -----------WS-C5508 WS-C5508 Modem Baud Traffic Peak Peak-Time ------- ----- ------- ---- ------------------------disable 9600 0% 0% Mon Jul 23 2001, 16:30:14 System Name System Location System Contact ------------------------ ------------------------ -------------Cat5K Corp HQ Closet 5 John Doe Cat5K (enable)
Configuring Logging and Passwords
Logging can be a very important tool when troubleshooting problems on any switch; however, the nearly endless barrage of syslog messages to the console and the default setting of unbuffered logging can lead to some headaches Therefore, setting the logging parameters of your switch is the next priority In addition, setting the enable, console, and telnet passwords is also a high priority because you never know who will want to hack your switches
Copyright © OnBarcode.com . All rights reserved.