SEVEN in .NET

Generator Data Matrix 2d barcode in .NET SEVEN

CHAPTER SEVEN
Data Matrix ECC200 Creator In .NET
Using Barcode printer for VS .NET Control to generate, create Data Matrix image in VS .NET applications.
Data Matrix Decoder In .NET Framework
Using Barcode scanner for VS .NET Control to read, scan read, scan image in VS .NET applications.
FIGURE 7-9 Two types of surge suppressors
Drawing Bar Code In Visual Studio .NET
Using Barcode creation for .NET framework Control to generate, create barcode image in VS .NET applications.
Recognize Barcode In VS .NET
Using Barcode decoder for Visual Studio .NET Control to read, scan read, scan image in VS .NET applications.
ENTRANCE INSTALLATION
Data Matrix Encoder In Visual C#.NET
Using Barcode creation for .NET Control to generate, create Data Matrix image in .NET framework applications.
Making Data Matrix ECC200 In .NET
Using Barcode printer for ASP.NET Control to generate, create Data Matrix 2d barcode image in ASP.NET applications.
The service entrance is very important inasmuch as it is the end of the distribution line for the utility Once the power has reached the user, and enters the property, it is up to the owner to see to it that the wiring inside meets code requirements Figure 7-12 shows the attention given to the service entrance riser support on a low building Note how far the meter is mounted above the ground This work is usually done by the electrician; at least 24-inch service conductors are left for connection by the power company when it brings power up to the house or building In most suburban developments, the electrical service is brought in from the line to the house by underground cables Figure 7-13 shows the requirements for such an installation This service shows the pole in the rear of the house Some localities also require that the entire electrical service to an area be underground This eliminates poles in the rear of the house The standards for a farm meter pole by a local power company are shown in Figure 7-14 Note the division of ownership Also, note the 5/8-inch by 8-foot ground rods at least 3 feet from the pole This is a single-phase, three-wire 120/240-volt installation for loads exceeding 40-kilowatt demand
ECC200 Creation In Visual Basic .NET
Using Barcode maker for Visual Studio .NET Control to generate, create Data Matrix 2d barcode image in .NET applications.
Generating Matrix Barcode In .NET Framework
Using Barcode drawer for Visual Studio .NET Control to generate, create 2D Barcode image in .NET framework applications.
INSTALLING THE LOAD CENTER
UPC Code Maker In VS .NET
Using Barcode generator for .NET Control to generate, create UPC Code image in .NET framework applications.
Barcode Generator In Visual Studio .NET
Using Barcode maker for .NET framework Control to generate, create barcode image in .NET applications.
The load center is usually the largest metal box located outside the house and serves as the termination of the service line from the power
1D Barcode Maker In Visual Studio .NET
Using Barcode drawer for .NET framework Control to generate, create Linear image in .NET framework applications.
Generate Planet In .NET
Using Barcode printer for VS .NET Control to generate, create USPS PLANET Barcode image in .NET framework applications.
Note #1 Note #2 Note #3
UPC-A Supplement 5 Encoder In VB.NET
Using Barcode generation for .NET Control to generate, create UPC Code image in VS .NET applications.
Data Matrix ECC200 Generation In C#.NET
Using Barcode generation for .NET framework Control to generate, create DataMatrix image in .NET framework applications.
Note 1 Service entrance cable or service entrance conductors in approved conduit 100 amp maximum capacity Note 2 Watertight fitting Note 3 Grounded conductor connected to socket trough ground stud by customer Note 4 Meter socket trough supplied by company Installed by customer Note 5 Neutral potential terminal required where service is single-phase 8 wire 277/480 volts connect to socket trough ground stud Note 6 Conductors to service equipment 100 amp maximum capacity Note 7 Service equipment Note 8 Connect grounded conductor to service equipment ground block Final grade Note 9 Install grounding electrode conductor in accordance with NEC requirements
DataMatrix Encoder In .NET Framework
Using Barcode maker for ASP.NET Control to generate, create Data Matrix ECC200 image in ASP.NET applications.
Bar Code Reader In Java
Using Barcode Control SDK for Java Control to generate, create, read, scan barcode image in Java applications.
Note #4
Painting Bar Code In Java
Using Barcode generation for Android Control to generate, create bar code image in Android applications.
Generate USS Code 39 In None
Using Barcode drawer for Microsoft Excel Control to generate, create Code-39 image in Microsoft Excel applications.
Note #5
UCC - 12 Drawer In None
Using Barcode generation for Font Control to generate, create EAN / UCC - 13 image in Font applications.
Generating DataMatrix In Visual Basic .NET
Using Barcode printer for Visual Studio .NET Control to generate, create Data Matrix ECC200 image in Visual Studio .NET applications.
Note #6 Note #7 Note #8 Note #9
4' to 5' 6"
Single-phase 3 wire 277/480 volts 100 amp maximum service entrance One-meter installation
FIGURE 7-10 1-meter installation
CHAPTER SEVEN
Note #1 Note #2
Note #3 Note #4 Note #5 Note #6 Note #7 Note #8 Note #9 Note #10 Final grade
Single-phase 3 wire 120/240 volts 150 amp Minimum service entrace Single-phase 3 wire 120/240 volts 150 amp Minimum service entrance Two- to six meter installation
4' to 5' 6"
Note 1 Service entrance cable or service entrance conductors in approved capacity 150ampere minimum capacity Note 2 Watertight fitting Note 3 Preloaded compression for 3/8" stud size to be furnished and installed by contractors Note 4 Grounded terminal for potential code required only where service is single-phase 8 wire 120/208 volts Connected to socket trough ground stud by customer Note 5 Grounded conductor Connected to socket trough ground stub by customer Note 6 Meter socket troughs supplied by company Installed by customer Multimeter channel cannot be modified for additional positions Note 7 Alternate service entrance location Note 8 Conductors to service equipment 150 ampere maximum per position Note 9 Connect grounded conductor to service equipment ground block Note 10 Install grounding electrode conductor in accordance with NEC requirements
FIGURE 7-11 Installation of 2 to 6 meters
company It may also be located inside the house or in the basement In order to t a speci c wiring problem it may be necessary to remove some knockouts and insert connectors to prevent the wire from being damaged as it is inserted into the box The following information locates the knockouts and provides the dimensions of the box in both inches and millimeters
Note #1 Note #2 Note #3 Note #4
Note #10 Note #11 48" Maximum 18" Minimum Note #12 Note #13 Note #14 Note #15
Copyright © OnBarcode.com . All rights reserved.