free 2d barcode generator asp.net TLFeBOOK in Software

Create Denso QR Bar Code in Software TLFeBOOK

TLFeBOOK
QR Code Encoder In None
Using Barcode generator for Software Control to generate, create QR Code JIS X 0510 image in Software applications.
Quick Response Code Recognizer In None
Using Barcode reader for Software Control to read, scan read, scan image in Software applications.
APPENDIX B
QR Code JIS X 0510 Creation In C#.NET
Using Barcode maker for .NET Control to generate, create Quick Response Code image in .NET applications.
QR Code ISO/IEC18004 Printer In VS .NET
Using Barcode encoder for ASP.NET Control to generate, create QR Code JIS X 0510 image in ASP.NET applications.
value at the joint or splice equal to the insulation value of the conductors The connectors shall be UL approved
QR Code Maker In .NET Framework
Using Barcode generator for VS .NET Control to generate, create QR Code 2d barcode image in Visual Studio .NET applications.
QR-Code Generator In Visual Basic .NET
Using Barcode creator for .NET framework Control to generate, create QR image in Visual Studio .NET applications.
Junction and Pull Boxes (A) The Electrical Contractor shall furnish and install all junction and pull boxes to
Printing Bar Code In None
Using Barcode creator for Software Control to generate, create barcode image in Software applications.
Code39 Generator In None
Using Barcode maker for Software Control to generate, create ANSI/AIM Code 39 image in Software applications.
provide access points for pulling and feeding conductors into a raceway system They shall be used in conduit runs where the number of bends between outlets exceeds the maximum number permitted by the current NEC Junction and pull boxes shall be located as shown on the drawings in the sizes indicated in the junction and pull box schedule
GTIN - 12 Maker In None
Using Barcode encoder for Software Control to generate, create UPC-A image in Software applications.
Draw Data Matrix ECC200 In None
Using Barcode maker for Software Control to generate, create ECC200 image in Software applications.
(B) Junction and pull boxes and their covers shall be formed from sheet steel and
Generate Code-128 In None
Using Barcode creator for Software Control to generate, create Code128 image in Software applications.
USS-128 Generation In None
Using Barcode creation for Software Control to generate, create GS1 128 image in Software applications.
shall have widths, heights, and depths as shown on the drawings or junction and pull box schedules and shall be finished in gray enamel paint Boxes without hinged covers shall include covers with attached screws
Encode I-2/5 In None
Using Barcode printer for Software Control to generate, create 2 of 5 Interleaved image in Software applications.
Generate Bar Code In Java
Using Barcode generator for Java Control to generate, create barcode image in Java applications.
(C) Junction and pull boxes shall be in industry standard sizes as manufactured
Bar Code Decoder In Java
Using Barcode Control SDK for Java Control to generate, create, read, scan barcode image in Java applications.
Printing ANSI/AIM Code 128 In Java
Using Barcode generator for Java Control to generate, create Code 128A image in Java applications.
Outlet Boxes
Bar Code Scanner In None
Using Barcode recognizer for Software Control to read, scan read, scan image in Software applications.
Painting Data Matrix ECC200 In Java
Using Barcode printer for Java Control to generate, create Data Matrix image in Java applications.
, or approved equivalent
Painting UPC-A Supplement 5 In .NET
Using Barcode creation for Reporting Service Control to generate, create UPC-A image in Reporting Service applications.
European Article Number 13 Printer In Java
Using Barcode creator for Java Control to generate, create EAN 13 image in Java applications.
(A) Outlet boxes with the correct fitting for the application shall be located at each
conductor splice point, at each outlet, switch point, or junction point, and at each pull point for the connection of conduit and other raceways They shall also be located at all transitions from conduit to open cables All outlet boxes for concealed wiring shall be made from galvanized- or cadmium-plated sheet steel, and they shall have a depth of at least 15 inches, whether single or ganged The boxes shall be large enough size to accommodate the number of wiring devices and conductors as specified in the fill schedule of the current NEC The depths, clamps, and number of knockouts shall be as specified in the outlet box schedule
(B) Rectangular 3- by 2-inch metal boxes shall be used for installing single switches
or duplex receptacles, as specified or shown on the drawings Two compatible boxes may be ganged together to accept two switches or two duplex receptacles at a single location or as specified or shown on the drawings
(C) Square 4- by 4-inch or 411 16 - by 411 16-inch metal boxes shall be used for
installing two switches or two duplex receptacles at a single location or as specified or shown on the drawings
(D) Octagonal 4- by 4-inch metal boxes shall be used for containing and protecting
wire connections for ceiling- or wall-mounted luminaires as specified or shown on the drawings The Electrical Contractor shall furnish all required telescoping metal braces, hickeys, covers, and miscellaneous hardware, as required
(E) Round ceiling metal pan boxes with diameters of 31 4 inches shall be used for
containing and protecting wire connections for ceiling- or wall-mounted lumi-
TLFeBOOK
APPENDIX B
naires as specified or shown on the drawings The Electrical Contractor shall furnish all hickeys, covers, clamps, and miscellaneous clamps, as required
(F) Telephone and communications boxes shall be as specified or shown on the
drawings
(G) Outlet boxes shall be in industry standard sizes as manufactured by
or approved equivalent
Wiring Devices (A) The wiring devices listed below by manufacturer and catalog number indicate the
quality and specification grade required In the judgment of the Electrical Contractor, wiring devices manufactured in the same style and dimensions that comply with the same tests and codes may be used without approval by the Architect/Engineer In cases where a device is specified with only one manufacturer and catalog or part number and without the phrase or equivalent, substitutions shall be made only with the approval of the Architect/Engineer
1 Wall-Mounted Switches Where more than one flush wall switch is indicated
in the same location, the switches shall be mounted in gangs under a common wallplate Device
a Single-pole switch, 20A/120V b Three-way switch, 20A/120V c Four-way switch, 20A/120V
Manufacturer and Catalog No Manufacturer and Catalog No
2 Wall-Mounted Receptacles, unless otherwise specified, shall be duplex
Device
a Receptacle, 20A/125V b Receptacle, 20A/250V c Receptacle, 20 A/120V GFCI , d Receptacle, 30 A/120V GFCI , e Receptacle, 20A/120V isolated ,
ground
(B) The following wiring devices are specified by only one manufacturer and cata-
log number; substitutions may be made only with the approval of the Architect/Engineer
a Dimmer switches b Pilot-light switches c Switch/receptacles
TLFeBOOK
APPENDIX B
d Timer switches e Motion sensors (C) The Electrical Contractor shall furnish and install appropriate wallplates for all
receptacles, switches, control devices, communications, and telephone outlets with a finish, and The wallplates shall be made of shall be in the color specified on the wallplate schedule Special markings shall be as indicated on the drawings or in the specifications
(D) Where wiring devices are installed in outlet boxes exposed to weather, the
boxes, wallplates, and covers shall be approved by the Architect/Engineer for those locations
Electrical Identification (A) The Electrical Contractor shall maintain accurate records of all deviations in work
as installed from work specified on the drawings or in the specifications On completion of the project, two (2) complete sets of marked-up prints showing these deviations shall be delivered to the Architect/Engineer
SERVICE AND DISTRIBUTION
General (A) The Electrical Contractor shall furnish and install an electric service entrance,
related distribution equipment, and an approved grounding system as shown on the drawings, and schedules shall comply with the current NEC, local and state building and electric codes, and Electric Utility specifications
Copyright © OnBarcode.com . All rights reserved.