free 2d barcode generator asp.net (C) The Electrical Contractor shall furnish the matching cable and conduit necessary in Software

Printing Denso QR Bar Code in Software (C) The Electrical Contractor shall furnish the matching cable and conduit necessary

(C) The Electrical Contractor shall furnish the matching cable and conduit necessary
QR Code ISO/IEC18004 Generator In None
Using Barcode encoder for Software Control to generate, create QR Code image in Software applications.
QR Code 2d Barcode Reader In None
Using Barcode reader for Software Control to read, scan read, scan image in Software applications.
to extend the service lateral from the service end box to the main disconnect inside the project building, as indicated in the drawings and specifications The Owner shall maintain at his or her own expense the required service lateral from this point to his or her main disconnect
Paint Quick Response Code In C#
Using Barcode creation for .NET framework Control to generate, create QR Code image in .NET applications.
QR Drawer In Visual Studio .NET
Using Barcode generator for ASP.NET Control to generate, create QR image in ASP.NET applications.
(D) Unless otherwise specified, the service lateral shall be three insulated conduc-
Denso QR Bar Code Drawer In .NET Framework
Using Barcode drawer for .NET Control to generate, create QR Code ISO/IEC18004 image in Visual Studio .NET applications.
Quick Response Code Drawer In Visual Basic .NET
Using Barcode generator for .NET Control to generate, create QR-Code image in .NET applications.
tors buried in a trench 2 to 4 feet deep below finished grade and a minimum of 4 inches wide
Generate EAN 128 In None
Using Barcode generator for Software Control to generate, create EAN / UCC - 14 image in Software applications.
Generate UCC - 12 In None
Using Barcode generator for Software Control to generate, create UPC Code image in Software applications.
(E) The Electrical Contractor shall mount the watthour meter and base plumb and
Printing GS1 - 13 In None
Using Barcode creator for Software Control to generate, create GS1 - 13 image in Software applications.
Generate Bar Code In None
Using Barcode printer for Software Control to generate, create barcode image in Software applications.
level at the distance above the finished grade specified or shown on the drawings For 200-ampere service, the service entrance conduit shall be 2-inch galvanized steel pipe threaded into the meter base Raintight threaded flange conduit connectors shall be located as shown on the drawings, and the metal conduit shall be strapped to the supporting wall with conduit straps not more than 54 inches apart
Paint Data Matrix ECC200 In None
Using Barcode creation for Software Control to generate, create DataMatrix image in Software applications.
Bar Code Encoder In None
Using Barcode creator for Software Control to generate, create barcode image in Software applications.
Service Entrance (A) The Electrical Contractor shall provide a service entrance system as shown on the
4-State Customer Barcode Maker In None
Using Barcode maker for Software Control to generate, create OneCode image in Software applications.
Making ECC200 In VB.NET
Using Barcode generator for .NET framework Control to generate, create Data Matrix image in VS .NET applications.
drawings and described in the specifications The Electrical Contractor shall calculate and verify the electrical demand requirements for the building prior to the installation of electric service
Printing Code 3/9 In Objective-C
Using Barcode printer for iPad Control to generate, create Code 39 Full ASCII image in iPad applications.
Create Barcode In None
Using Barcode printer for Online Control to generate, create bar code image in Online applications.
(B) The electrical systems shall be a 120-volt, 60-Hertz, single-phase, three-wire service Grounding (A) Unless otherwise specified or determined by local building code, the Electrical
Bar Code Creation In VS .NET
Using Barcode encoder for Reporting Service Control to generate, create barcode image in Reporting Service applications.
EAN-13 Maker In VS .NET
Using Barcode generation for Reporting Service Control to generate, create EAN13 image in Reporting Service applications.
Contractor shall measure ground resistance with an approved Megger groundresistance tester to determine the requirement for more than one ground rod as specified in the current NEC
Bar Code Maker In None
Using Barcode drawer for Font Control to generate, create bar code image in Font applications.
Decoding Code 3/9 In VS .NET
Using Barcode recognizer for Visual Studio .NET Control to read, scan read, scan image in .NET applications.
(B) In addition to the ground rod(s), the Electrical Contractor shall make approved
connections to one other earth ground, a metal cold water pipe or as approved by the NEC In no case shall a gas pipe be used as an earth ground The grounding wire shall be at least No 6 AWG copper protected by PVC conduit if exposed above ground at any outside location All ground clamps shall be approved for the intended purpose
TLFeBOOK
APPENDIX B
(C) If a second ground rod is specified, it shall be separated at least 6 feet from the
first, assuming vertical orientation of the rods
Branch-Circuit Panelboards/Loadcenters (A) Lighting and appliance branch-circuit panelboards (loadcenters) shall be made
from cold-rolled steel and shall be finish painted in the manufacturer s colors It shall consist of three main parts: front cover, inner cover, and backpan built to accept molded branch circuit breakers rated for 240 volts or less
(B) The branch-circuit panelboard shall be equipped with parallel hot buses with suf-
ficient stabs to accept the number and type of circuit breakers specified for the project and have room to spare for later expansion The back pan shall contain a rail for effective clamping of all circuit breakers The parallel neutral/ground buses shall be made from solid, rectangular copper alloy with screw-type wire terminals The backpan shall be large enough to provide adequate gutter space around the busbars for the anticipated wire fill It shall have sufficient knockouts for the number and position of cables specified The front cover shall be provided with a secure latch and concealed hinges
(C) The branch-circuit panelboard shall be UL listed for indoor applications, bear the
UL label, and meet NEMA and ANSI requirements It shall also conform to the current NEC for switchboards and panelboards and the insertion of overcurrent devices
(D) The branch-circuit panelboard shall be NEMA Type 1, as manufactured by
or approved equivalent, and shall be fully assembled with all hot and neutral/ground buses, gutter posts, tie bar, and other ancillary fittings It shall be durably marked in accordance with the current NEC
(E) The Electrical Contractor shall make every reasonable effort to balance the load
to the satisfaction of the Electric Utility The Electrical Contractor shall complete the panelboard directory on the inner face of the front cover legibly to identify all circuits in a permanent manner, as approved by the Owner
Overcurrent Protective Devices (A) The Electrical Contractor shall furnish and install, where indicated on the draw-
ing or as required by the current NEC, main and branch circuit breakers The breakers shall be capable of manual operation and opening all poles simultaneously The tripping mechanism shall operate thermally, magnetically, or both, shall open instantaneously on short circuits, and have a time delay on overcurrent The circuit breakers shall be of the type shown on the drawings or called out in the protective device schedule
Copyright © OnBarcode.com . All rights reserved.