barcode vb.net 2010 Installing Antennas in Software

Draw PDF 417 in Software Installing Antennas

Installing Antennas
PDF417 Drawer In None
Using Barcode drawer for Software Control to generate, create PDF417 image in Software applications.
Scanning PDF-417 2d Barcode In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
Attach the feedline to the mast every 8 to 16 inches with one to two wraps of electrical tape or plastic cable ties I indicated black cable ties in the materials list above because the black ones are typically ultraviolet resistant and will not break down and crack off over time The white nylon and decorator colored ties will disintegrate more quickly in the sunlight Leave 2 to 4 feet of the mast free so that you can position it into the mounting without the cable being in the way You are now ready to raise the mast and get underway A 5- or 10-foot mast pipe is not that heavy and may be raised by one person, but a 20-foot pipe is a lot heavier, and you have the additional weight of the antenna and feedline to consider when you move it around Get help if you need it! You will need help if you are using a tilt-over base plate and guy wires, as it is impossible (as far as I know) for one person to set and hold the mast upright and move around to set all the guy wires at their anchor points So, set the mast into the tripod or base plate If you are using a tripod, secure the mast in place with the anchor bolts provided and you are just about done For tilt-over methods, ensure the mast is vertical with a level and do a final adjustment and setting of the guy wires Complete the fastening of the feedline to the mast, allowing some extra space to loop around the upper brackets of the tripod And if you have a directional antenna, perform at least a visual alignment of it to the direction of interest If there is an active access point already operating at the other end, you may be able to use your computer and the NetStumbler program to fine-tune the alignment for highest signal strength If there is no active signal at the other end, you will probably be doing some trial-and-error realignments at each end to optimize the signal Your next step is to attach one end of your ground wire to the mounting base Whether you then tape or cable-tie the ground wire and signal feedline together or not depends on the destination for each wire something to consider in setting the ground rod in place Complete the running of the wires to the edge of your roof, avoiding any places that may scrape the wire and open it up, and avoiding locations where the wire may get stepped on Before going farther, play out some excess wire to form a downward loop at the edge or below the eaves or awning This is a drip loop and will keep water from flowing along the remaining length of wires into your house or office Bring the end of the loop up and fasten the wires under the
Creating PDF417 In Visual C#
Using Barcode creation for Visual Studio .NET Control to generate, create PDF-417 2d barcode image in .NET applications.
Encoding PDF 417 In Visual Studio .NET
Using Barcode maker for ASP.NET Control to generate, create PDF-417 2d barcode image in ASP.NET applications.
16
Generating PDF 417 In VS .NET
Using Barcode creation for Visual Studio .NET Control to generate, create PDF 417 image in Visual Studio .NET applications.
PDF-417 2d Barcode Generator In Visual Basic .NET
Using Barcode encoder for .NET Control to generate, create PDF417 image in .NET framework applications.
eaves to complete the loop; then continue to run the wire to its destination An additional drip loop may be necessary before the wire enters the structure if it is exposed to the elements at that point Seal any holes with latex caulking and finish the feedline run to your wireless device, and the ground wiring to your ground rod or a cold water pipe Clean up your mess, throw away the debris, put your ladder and tools away, and enjoy your new stronger wireless signal!
Bar Code Generation In None
Using Barcode generator for Software Control to generate, create barcode image in Software applications.
Painting Code 3 Of 9 In None
Using Barcode creator for Software Control to generate, create USS Code 39 image in Software applications.
A Few Final Hints
ECC200 Printer In None
Using Barcode printer for Software Control to generate, create Data Matrix 2d barcode image in Software applications.
Create UPC-A Supplement 2 In None
Using Barcode creator for Software Control to generate, create UPCA image in Software applications.
If you have a choice of materials when buying connectors, choose silver-plated ones I prefer and would suggest gold-plated, and for some smaller connectors, you may not have a choice But I don t know of any gold-plated large form connectors like the Type N Nickel or brass connectors may look nice, but they do not weather well Silverplating oxidizes in a good way silver-oxide is actually a better conductor When copper, chrome, or brass weather, they tend to lose conductivity, especially when mated with dissimilar metals, and this can adversely affect your signal or create noise spots that allow for interference to your system or those of others If you are extra cautious or simply want to add value and longevity to your system, you may consider installing a lightning protector in your feedline at the point it enters or just after it has entered your structure A lightning protector is a device that detects and reacts quickly to the presence of high voltage on the line and shorts it to ground, hopefully before damaging your equipment You will need to attach a ground wire to this device for it to be most effective A variety of protectors are available from most wireless equipment vendors like HyperLink Technologies, but if you are looking for a brand-name recommendation, one manufacturer preferred by most communications sites is Poly-Phaser (http://wwwpolyphasercom) Lightning and overvoltage protectors are also available for Ethernet cabling and are highly recommended for power-over-Ethernet applications If lightning seems to be the least of your worries, take a look at Figure 168 This is a picture of what was a 6-inch diameter, 1/2-inch thick Teflon insulator used as the spacer/dielectric between the center conductor and outer shield pipe of a transmission line from a 15
Encoding Code 128 In None
Using Barcode generator for Software Control to generate, create Code 128 Code Set C image in Software applications.
Draw Barcode In None
Using Barcode encoder for Software Control to generate, create barcode image in Software applications.
Identcode Maker In None
Using Barcode encoder for Software Control to generate, create Identcode image in Software applications.
Make Code39 In Visual Basic .NET
Using Barcode printer for .NET Control to generate, create Code 39 Full ASCII image in Visual Studio .NET applications.
GS1-128 Creator In Visual Studio .NET
Using Barcode encoder for Reporting Service Control to generate, create UCC - 12 image in Reporting Service applications.
USS-128 Encoder In Objective-C
Using Barcode creator for iPad Control to generate, create EAN 128 image in iPad applications.
Print Barcode In Java
Using Barcode drawer for Eclipse BIRT Control to generate, create barcode image in BIRT applications.
Code 128 Printer In Java
Using Barcode drawer for Java Control to generate, create Code128 image in Java applications.
1D Creator In Visual Basic .NET
Using Barcode encoder for .NET Control to generate, create 1D Barcode image in .NET framework applications.
Paint Matrix 2D Barcode In .NET
Using Barcode drawer for .NET framework Control to generate, create Matrix 2D Barcode image in .NET applications.
Copyright © OnBarcode.com . All rights reserved.