qr code generator vb.net open source Routing Protocols in Visual Studio .NET

Generation ANSI/AIM Code 39 in Visual Studio .NET Routing Protocols

Routing Protocols
Encoding USS Code 39 In .NET
Using Barcode maker for Visual Studio .NET Control to generate, create Code 39 Full ASCII image in Visual Studio .NET applications.
Recognize ANSI/AIM Code 39 In VS .NET
Using Barcode scanner for VS .NET Control to read, scan read, scan image in VS .NET applications.
Windows Server 2008 supports the following routing protocols: Dynamic Host Configuration Protocol (DHCP) Relay Agent DHCPv6 Relay Agent Internet Group Management Protocol (IGMP) Router and Proxy NAT RIPv2 for Internet Protocol
Creating Barcode In .NET
Using Barcode drawer for VS .NET Control to generate, create bar code image in VS .NET applications.
Barcode Recognizer In VS .NET
Using Barcode scanner for .NET framework Control to read, scan read, scan image in VS .NET applications.
Microsoft Windows Server 2008 Administration
Code 3/9 Printer In C#.NET
Using Barcode maker for .NET Control to generate, create Code 3/9 image in .NET framework applications.
Encode Code39 In .NET Framework
Using Barcode creation for ASP.NET Control to generate, create Code-39 image in ASP.NET applications.
Figure 11-6 IPv4 General network interface information
Painting ANSI/AIM Code 39 In VB.NET
Using Barcode creator for VS .NET Control to generate, create Code 39 image in .NET framework applications.
Create Code 39 Full ASCII In Visual Studio .NET
Using Barcode drawer for .NET framework Control to generate, create Code39 image in VS .NET applications.
The DHCP relay agents facilitate DHCP request forwarding over the routers They come in both standard IPv4 and the new IPv6 flavors IGMP is used between routers to negotiate and manage multicast groups NAT is typically used when you want to connect or hide a number of internal hosts from another network For example, if you want to connect your computers to the Internet and only one valid external IP address is available, you can use NAT to translate all your internal IP addresses out through your external IP RIPv2 is used for dynamic route discovery between routers, up to 15 routers deep
Code 128C Generation In Visual Studio .NET
Using Barcode printer for Visual Studio .NET Control to generate, create Code 128C image in .NET applications.
Barcode Maker In .NET Framework
Using Barcode maker for Visual Studio .NET Control to generate, create bar code image in .NET framework applications.
Hands-On Exercise: Installing and Configure RIPv2 for IP
Encoding European Article Number 13 In Visual Studio .NET
Using Barcode maker for .NET framework Control to generate, create European Article Number 13 image in .NET applications.
Identcode Encoder In Visual Studio .NET
Using Barcode encoder for .NET framework Control to generate, create Identcode image in VS .NET applications.
In this exercise, we install RIPv2 for IP and configure its various properties We configure RIP to work only with RIPv2-compatible routers to increase its efficiency
Code 39 Extended Drawer In None
Using Barcode maker for Microsoft Excel Control to generate, create Code 39 image in Office Excel applications.
Bar Code Creator In .NET
Using Barcode generator for Reporting Service Control to generate, create bar code image in Reporting Service applications.
11:
UPC-A Scanner In C#.NET
Using Barcode recognizer for Visual Studio .NET Control to read, scan read, scan image in .NET framework applications.
Bar Code Recognizer In Visual Basic .NET
Using Barcode decoder for VS .NET Control to read, scan read, scan image in .NET applications.
Routing and Remote Access
Make Barcode In Java
Using Barcode creation for Android Control to generate, create bar code image in Android applications.
Bar Code Recognizer In Java
Using Barcode Control SDK for BIRT Control to generate, create, read, scan barcode image in BIRT applications.
Figure 11-7 IPv4 network interface properties
Create UPC-A Supplement 5 In None
Using Barcode drawer for Online Control to generate, create GS1 - 12 image in Online applications.
European Article Number 13 Creator In None
Using Barcode drawer for Software Control to generate, create EAN13 image in Software applications.
1 Open the Routing and Remote Access management console 2 Expand your server name 3 Expand IPv4 4 Right-click General and select New Routing Protocol 5 Select RIP Version 2 for Internet Protocol (Figure 11-8), and then click OK 6 Right-click the newly create RIP icon under IPv4 and select New Interface 7 Select Local Area Connection, and then click OK (Figure 11-9) 8 Select Periodic Update Mode as the Operation Mode 9 Select RIP Version 2 Multicast for the Outgoing Packet Protocol
Microsoft Windows Server 2008 Administration
Setting Enable IP Router Management
Description Toggles whether this interface participates in IP routing It toggles the administrative status from up and down Unless this checkbox is enabled, you cannot route through this interface Defines whether the router enables automatic router discovery through router discovery messages When checked, it enables the advertisement-related options Indicates the number of minutes an advertisement is valid Once the advertisement has expired, it is no longer accepted by the clients Defines a numeric value to indicate this router s level of preference The higher the number, the more clients will prefer to use this router Defines the minimum and maximum time intervals when advertisements are sent This values provides routers with a range of time when it can randomly select to advertise to avoid having all routers advertise at the same time Defines filters for which packets are allowed in through this interface For example, you can block all traffic coming from a specific network and even restrict by protocol Works the same as Inbound Filters except applies to outbound packets through this interface Allows the router to block any fragmented packets This is useful to prevent denial-of-service attacks caused by fragmented packets Use this with caution, however, because some applications work by using fragmented packets, and enabling this option will prevent that application from communicating
Enable Router Discovery Advertisements
Advertisement Lifetime (Minutes) Level of Preference
Send Out Advertisements Within This Interval
Inbound Filters
Outbound Filters Enable Fragmentation Checking
Table 11-1 IPv4 Network Interface General Properties
11:
Routing and Remote Access
Figure 11-8 Installing RIPv2 for IP
10 Select RIP Version 2 Only as the Incoming Packet Protocol The General tab should now look like Figure 11-10 11 Click the Security tab and make sure that all routes are accepted for incoming routes and all routes are announced for the outgoing routes (Figure 11-11) 12 Click the Neighbors tab Here you can define how this router will interact with other RIP routers Select Use Broadcast or Multicast Only, as shown in Figure 11-12 If you want to provide specific routers with which RIP can communicate, you could enter their IP addresses here as its neighbors 13 Click the Advanced tab, change the Periodic Announcement Interval to 60 seconds, and then click OK to save the changes (Figure 11-13)
Microsoft Windows Server 2008 Administration
Figure 11-9 Creating a new RIPv2 interface
A Closer Look at RIPv2 Properties
The preceding exercise covered installing and configuring RIPv2 for IP on Windows Server 2008 and covered only a handful of settings for RIPv2 Let s look more closely at the different options you can set and what effect they have on the RIP behavior Referring to Figure 11-10, you can change the following settings on the General tab: Operation Mode Can be Periodic Update (default for LAN interfaces) or Auto-static Update (default for demand-dial interfaces) In general, you want auto-static whenever a link is not connected at all times but you want that route to stay valid on all your routers between updates even when the connection is down
11:
Copyright © OnBarcode.com . All rights reserved.