Perimeter Security in Software

Generation PDF-417 2d barcode in Software Perimeter Security

Perimeter Security
PDF-417 2d Barcode Reader In None
Using Barcode Control SDK for Software Control to generate, create, read, scan barcode image in Software applications.
Painting PDF 417 In None
Using Barcode generation for Software Control to generate, create PDF417 image in Software applications.
ASSESSMENT FOR BLAST PROTECTION
PDF417 Reader In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
Make PDF-417 2d Barcode In C#.NET
Using Barcode encoder for Visual Studio .NET Control to generate, create PDF-417 2d barcode image in .NET framework applications.
As stated earlier, the first step in the assessment process for designing blast protection for a building or structure is to define the use This will help in determining the risk factor of being a bombing target Targets for bombing are usually buildings defined as soft targets that are easy to get close to and experience the most damage The following questions from FEMA will help in defining the building s main purpose or function: 1 What are the building s primary services or outputs 2 What are the critical activities that take place at the building 3 What goes on in the building Are there many visitors and who are they 4 What external sources are required for the building s success The answers to the questions above outline what the building does or will do This is important in defining the risk For example, buildings with large numbers of people that have a direct effect on the economy are at greater risk than an empty storage building Health care, schools, government buildings are also considered to be a high risk After the building s main function has been identified, the next step is to identify the key infrastructure of the building The reason for identifying the key infrastructure is because that is where blast protection design will applied The most important part of any building is the people and the correlation to the damage of the infrastructure and the number of people that can be killed in a bomb blast needs to be evaluated Damage to the infrastructure that results in partial or total collapse of the building needs to be protected so the loss of the infrastructure will not result in a catastrophic loss What goes on or will go on in a building is an important part of the assessment A health care facility that has a large number of ambulatory patients is a high risk since the occupants cannot evacuate to a designated safe area without assistance Are there a sufficient number of exits to launch a full scale evacuation of the entire building What if one exit is destroyed or otherwise impassible If there are only two exits, will the remaining one be adequate This is an important question that needs to be addressed because if the number of evacuation routes will not be adequate to handle the number of people if one exit is lost, then the decision to provide some means of blast protection needs to be considered FEMA has developed a rating matrix that is used to categorize the asset value of each critical building component People rate the highest on the scale The scale is from very low to very high and a numerical value from 1-10 Table 16-1 shows the matrix rating system in a table format One table can be used to rate all of the assets until completed Each asset is given a rating based on the table
PDF-417 2d Barcode Creation In VS .NET
Using Barcode maker for ASP.NET Control to generate, create PDF417 image in ASP.NET applications.
Create PDF417 In VS .NET
Using Barcode printer for Visual Studio .NET Control to generate, create PDF417 image in .NET framework applications.
Blast Protection
PDF417 Encoder In VB.NET
Using Barcode creation for .NET framework Control to generate, create PDF-417 2d barcode image in VS .NET applications.
Code 128A Maker In None
Using Barcode creation for Software Control to generate, create Code 128A image in Software applications.
TABLE 16-1 FEMA Rating Scale
Barcode Drawer In None
Using Barcode encoder for Software Control to generate, create barcode image in Software applications.
Painting Data Matrix ECC200 In None
Using Barcode printer for Software Control to generate, create Data Matrix image in Software applications.
ASSET VERY LOW 1 LOW 2-3 MEDIUM LOW 4 MEDIUM 5-6 MEDIUM HIGH 7 HIGH 8-9 VERY HIGH 10
UPC-A Supplement 5 Generation In None
Using Barcode encoder for Software Control to generate, create UCC - 12 image in Software applications.
USS Code 39 Encoder In None
Using Barcode printer for Software Control to generate, create Code 39 image in Software applications.
and then that rating would be included in showing an overall rating for all of the building s assets Those assets with ratings that are considered unacceptable in the high to very high range would be part of the risk mitigation plan After the assets are rated, a threat and hazard assessment (vulnerability assessment) is done This is similar to any threat and vulnerability assessment FEMA recommends that the threat and vulnerability be obtained from local law enforcement, emergency management, FBI, or Homeland Security The vulnerability and threat assessment risk will be rated from high to low or the FEMA table used above can be used to rate the vulnerabilities and threats The point is not what rating system is used but to quantify the risk so it is meaningful and the risks can be prioritized By prioritizing the risks, a plan can be developed to mitigate the highest risks which would include blast protection for new and existing buildings especially those buildings that are high risk or a high value asset The vulnerabilities were outlined by completing the information for Table 16-1 All assets were identified and then prioritized by importance Now the threats need to be identified A threat is what could happen to the vulnerability to have an incident The information on how to perform a risk analysis is in 2 There is also a rating system form low to high that can be used or the same rating system and table presented earlier, developed by FEMA, can be used to rate the risk The vulnerability assessment can be done using a form that covers all the elements to be reviewed It is part of doing the physical security assessment There are a number of forms available or you can make your own form The form in Figure 2-2 in 2 can be used by adding the sections that address the blast vulnerabilities of the facility The sections that are different from the standard vulnerability form are the following items except for the security systems and security master plan:
Creating RM4SCC In None
Using Barcode generator for Software Control to generate, create Royal Mail Barcode image in Software applications.
UCC-128 Creator In Objective-C
Using Barcode printer for iPhone Control to generate, create GS1 128 image in iPhone applications.
UCC-128 Printer In Java
Using Barcode encoder for Java Control to generate, create EAN 128 image in Java applications.
Barcode Reader In VB.NET
Using Barcode Control SDK for VS .NET Control to generate, create, read, scan barcode image in .NET applications.
Recognize UPC - 13 In None
Using Barcode scanner for Software Control to read, scan read, scan image in Software applications.
Draw DataMatrix In None
Using Barcode maker for Online Control to generate, create DataMatrix image in Online applications.
UPC-A Supplement 5 Drawer In VS .NET
Using Barcode creation for Reporting Service Control to generate, create GS1 - 12 image in Reporting Service applications.
Barcode Reader In VS .NET
Using Barcode decoder for VS .NET Control to read, scan read, scan image in .NET applications.
Copyright © OnBarcode.com . All rights reserved.