barcode generator vb.net code TELE-ALERT in Software

Drawing Code-128 in Software TELE-ALERT

256 TELE-ALERT
Decoding Code 128 Code Set C In None
Using Barcode Control SDK for Software Control to generate, create, read, scan barcode image in Software applications.
Encoding Code 128C In None
Using Barcode drawer for Software Control to generate, create Code-128 image in Software applications.
Operating Tele-Alert
Code 128C Scanner In None
Using Barcode recognizer for Software Control to read, scan read, scan image in Software applications.
Drawing Code 128 Code Set A In C#.NET
Using Barcode drawer for .NET framework Control to generate, create Code128 image in .NET applications.
Operation of the Tele-Alert is simple, First you will need to connect a 9-V wall wart power supply to the circuit via the two power input pins at the top of the board. Next you will need to make up a serial communication or programming cable that connects the TeleAlert header J5 to the serial port of your programming computer; see Fig. 19-4. Now you will need to fire up you PC and load the supplied disk into your computer. Make a directory called TELE and dump the contents of the disk into that directory. Once the communication cable has been attached, you will need to load the STAMPW.EXE program. This is the STAMP 2 editor program you will use to load the Tele-Alert program into the microprocessor. You should also see the CELL.BS2 (Listing 19-1) program, which is used to operate the Tele-Alert system. Start the STAMPW.EXE program, and then scroll through the list and highlight the Tele-Alert program, titled CELL.BS2. Press enter and the program should be now displayed on the screen. Scroll down the displayed program, and look for the simulated phone number and replace it with your own phone number. Remember, a digit 10 is programmed by a zero. If you want to dial a long-distance number, just add the full sequence of numbers. If you wish to dial out from a PBX telephone system, you will need to first put in the access number such as an 8 or 9 followed by a comma and the actual phone number. Next, press ALT-R to load the program into the Tele-Alert circuit. The program produces different sequences of tone, which are transmitted to your remote cell phone. The tone sequences can be changed for your particular needs. You can change these sequences to songs if you choose. Your Tele-Alert is now programmed and ready to operate. At last, you can connect your event or alarm inputs to the set of solder pads at the far edge of the circuit board, just below the phone line connection (see Table 19-1). Remember, you must use normally open circuit switches for the alarm inputs unless you are using the optional motion module, which provides both normally open and normally closed inputs. Connect your phone line via the phone jack and your Tele-Alert is now ready to serve you. Now you are ready to simulate an alarm condition, to see if your Tele-Alert functions. You can test the circuit in one of two ways. A simulated approach is to connect a crystal headphone across the secondary of T1 at J6, with the Tele-Alert disconnected from the
Code 128C Generator In VS .NET
Using Barcode generator for ASP.NET Control to generate, create Code 128A image in ASP.NET applications.
Code 128 Creator In .NET Framework
Using Barcode encoder for .NET framework Control to generate, create Code 128B image in VS .NET applications.
Programming cable to PC J5-1 J5-2 J5-3 J5-4
Encoding Code-128 In Visual Basic .NET
Using Barcode generation for Visual Studio .NET Control to generate, create Code 128 Code Set B image in .NET applications.
EAN-13 Generation In None
Using Barcode generation for Software Control to generate, create GTIN - 13 image in Software applications.
1 2 3 4 5
Code128 Printer In None
Using Barcode creator for Software Control to generate, create Code 128C image in Software applications.
Generating Data Matrix In None
Using Barcode maker for Software Control to generate, create ECC200 image in Software applications.
Figure 19-4 Programming cable.
Barcode Printer In None
Using Barcode drawer for Software Control to generate, create barcode image in Software applications.
Code 39 Full ASCII Creator In None
Using Barcode creator for Software Control to generate, create Code 39 image in Software applications.
OPERATING TELE-ALERT 257
EAN-8 Supplement 2 Add-On Creator In None
Using Barcode generator for Software Control to generate, create GS1 - 8 image in Software applications.
Decoding ANSI/AIM Code 39 In Java
Using Barcode decoder for Java Control to read, scan read, scan image in Java applications.
'CELL2.BS2 'inputs go to +5 volts for activation flash Var byte new_io_state Var byte old_io_state Var byte call_state Var byte 'Set up conditions io Var byte timer Var byte i Var byte j Var word TXpin Con 10 LedPin Con 15 Lamp Con 13 Siren Con 12 Tele Con 9 MIC Con 8 recall_delay Con 120 C Con 3000 'C - 523 'Tones used for annunciation D Con 2000 'D - 587 E Con 1000 'E - 659 F Con 500 'F - 698 G Con 250 'G - 783 A Con 150 'A - 880 B Con 100 'B - 987 R Con 0 init: DIRL = %00000000 DIRH = %11111111 new_io_state = %00000000 old_io_state = %00000000 for flash = 1 to 3 high LedPin pause 1500 low LedPin pause 1500 next 'Init conditions
UPC-A Supplement 5 Creator In None
Using Barcode printer for Online Control to generate, create Universal Product Code version A image in Online applications.
Encoding Code 3/9 In None
Using Barcode creation for Word Control to generate, create Code 3/9 image in Word applications.
'indicate status conditions
Drawing Code 3/9 In None
Using Barcode creation for Office Excel Control to generate, create Code 3 of 9 image in Excel applications.
Code-128 Generator In Visual C#.NET
Using Barcode encoder for .NET framework Control to generate, create Code-128 image in .NET applications.
main: 'main start routine high LedPin new_io_state=INL pause 100 low LedPin pause 100 if new_io_state <> %00000000 then dial_cell after_io1: old_io_state = new_io_state goto main delay_and_scan old_io_state = new_io_state for timer = 1 to recall_delay high LEDPin new_io_state=INL pause 500 'check old/new compare input
Scan EAN / UCC - 13 In Visual C#.NET
Using Barcode decoder for .NET framework Control to read, scan read, scan image in .NET framework applications.
Barcode Reader In Visual Basic .NET
Using Barcode decoder for .NET framework Control to read, scan read, scan image in VS .NET applications.
Copyright © OnBarcode.com . All rights reserved.