barcode project in vb.net Transport Technologies in Software

Create Code 39 Extended in Software Transport Technologies

Transport Technologies
USS Code 39 Decoder In None
Using Barcode Control SDK for Software Control to generate, create, read, scan barcode image in Software applications.
Encoding Code 39 Extended In None
Using Barcode creation for Software Control to generate, create USS Code 39 image in Software applications.
Figure 7-16 Components of a typical optical network
ANSI/AIM Code 39 Reader In None
Using Barcode recognizer for Software Control to read, scan read, scan image in Software applications.
Make Code39 In C#
Using Barcode generation for .NET framework Control to generate, create USS Code 39 image in .NET applications.
7
Code39 Encoder In .NET Framework
Using Barcode creation for ASP.NET Control to generate, create ANSI/AIM Code 39 image in ASP.NET applications.
Code 3/9 Generation In VS .NET
Using Barcode encoder for Visual Studio .NET Control to generate, create Code 39 Full ASCII image in .NET applications.
Fundamentals of Optical Networking
Draw Code 3/9 In Visual Basic .NET
Using Barcode encoder for Visual Studio .NET Control to generate, create Code 39 Extended image in .NET framework applications.
UPC - 13 Printer In None
Using Barcode encoder for Software Control to generate, create EAN13 image in Software applications.
At their most basic level, optical networks require three fundamental components, as shown in Figure 7-16: a source of light, a medium over which to transport it, and a receiver for the light. Additionally, there may be regenerators, optical amplifiers, and other pieces of equipment in the circuit. We will examine each of these generic components in turn.
Create Code-39 In None
Using Barcode maker for Software Control to generate, create ANSI/AIM Code 39 image in Software applications.
UPC-A Supplement 5 Generator In None
Using Barcode encoder for Software Control to generate, create GS1 - 12 image in Software applications.
Optical Sources
Print Bar Code In None
Using Barcode drawer for Software Control to generate, create barcode image in Software applications.
Barcode Creation In None
Using Barcode generator for Software Control to generate, create barcode image in Software applications.
Today the most common sources of light for optical systems are either light-emitting diodes or laser diodes. Both are commonly used, although laser diodes have become more common for high-speed data applications because of their coherent signal. While lasers have gone through several iterations over the years including ruby rod and helium-neon, semiconductor lasers became the norm shortly after their introduction in the early 1960s because of their low cost and high stability.
Creating MSI Plessey In None
Using Barcode generation for Software Control to generate, create MSI Plessey image in Software applications.
Encoding Data Matrix ECC200 In None
Using Barcode printer for Font Control to generate, create ECC200 image in Font applications.
Light-Emitting Diodes (LEDs)
Bar Code Recognizer In Visual C#
Using Barcode scanner for VS .NET Control to read, scan read, scan image in Visual Studio .NET applications.
Paint Code 128B In Java
Using Barcode maker for Android Control to generate, create Code 128 image in Android applications.
LEDs come in two varieties: surface-emitting LEDs and edge-emitting LEDs. Surface-emitting LEDs give off light at a wide angle and therefore do not lend themselves to the more coherent requirements of optical data systems because of the difficulty involved in focusing their emitted light into the core of the receiving fiber. Instead, they are often used as indicators and signaling devices. They are, however, quite inexpensive, and are therefore commonly found.
Making Code 3/9 In Objective-C
Using Barcode drawer for iPad Control to generate, create ANSI/AIM Code 39 image in iPad applications.
Scan EAN 13 In None
Using Barcode decoder for Software Control to read, scan read, scan image in Software applications.
Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website.
UPC-A Generator In None
Using Barcode drawer for Font Control to generate, create UPC-A image in Font applications.
Barcode Drawer In Java
Using Barcode generation for Java Control to generate, create barcode image in Java applications.
Transport Technologies
Transport Technologies
An alternative to the surface-emitting LED is the edge-emitting device. Edge emitters produce light at significantly narrower angles and have a smaller emitting area, which means that more of their emitted light can be focused into the core. They are typically faster devices than surface emitters, but do have a downside: They are temperature sensitive and, therefore, must be installed in environmentally controlled devices to ensure the stability of the transmitted signal.
Laser Diodes
Laser diodes represent the alternative to LEDs. A laser diode has a very small emitting surface, usually no larger than a few microns in diameter, which means that a great deal of the emitted light can be directed into the fiber. Because they represent a coherent source, the emission angle of a laser diode is extremely narrow. It is the fastest of the three devices.
Optical Fiber
When Peter Schultz, Donald Keck, and Robert Maurer began their work at Corning to create a low-loss optical fiber, they did so using a newly crafted process called inside vapor deposition (IVD). Whereas most glass is manufactured by melting and reshaping silica, IVD deposits various combinations of carefully selected compounds on the inside surface of a silica tube. The tube becomes the cladding of the fiber; the vapordeposited compounds become the core. The compounds are typically silicon chloride (SiCl4) and oxygen (O2), which are reacted under heat to form a soft, sooty deposit of silicon dioxide (SiO2), as shown in Figure 717. In some cases, impurities such as germanium are added at this time to cause various effects in the finished product. In practice, the SiCl 4 and O2 are pumped into the fused silica tube as gases; the tube is heated in a high-temperature lathe, causing the sooty deposit to collect on the inside surface of the tube. The continued heating of the tube causes the soot to fuse into a glasslike substance. This process can be repeated as many times as required to create a graded refractive index, if required. Ultimately, once the deposits are complete, the entire assembly is heated fiercely, which causes the tube to collapse, creating what is known in the optical fiber industry as a preform. An example of a preform is shown in Figure 7-18.
Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website.
Copyright © OnBarcode.com . All rights reserved.