barcode printing in vb.net Indirect-fired storage water heaters in Visual Studio .NET

Maker QR in Visual Studio .NET Indirect-fired storage water heaters

Indirect-fired storage water heaters
QR-Code Decoder In Visual Studio .NET
Using Barcode Control SDK for VS .NET Control to generate, create, read, scan barcode image in Visual Studio .NET applications.
Generate QR Code JIS X 0510 In Visual Studio .NET
Using Barcode creator for .NET framework Control to generate, create QR Code image in VS .NET applications.
In the mid-1970s, a new type of water heater, an indirect-fired storage water heater, was developed. The unit is called indirect-fired because the medium used for heating the domestic water is boiler water, which itself is heated in a separate boiler used for either central heating or space heating. The boiler water circulates through a heat exchanger that is located either within the heater tank or in an external compartment. Figure 16-10 shows one type of indirect-fired storage water heater. This unit has a specially designed heat-exchanger coil mounted in the base of the tank. Hot boiler water flows through the coil, which is surrounded by domestic water. The design of the heat exchanger, which consists of an inner core surrounded by an outer helical coil, is such that it results in a relatively high recovery rate. The typical capacity of this residential indirect-fired water heater is about 40 gallons. With water heaters, whether there is an adequate supply will depend not only on the capacity but also on the recovery rate of the unit. The actual rate will depend on the Btu rating of the boiler that feeds the heat exchanger. For a typical house with a boiler that has an output rating of about 100,000 Btu per hour, the recovery rate is about 90 gallons per hour. The indirect-fired storage water heater works off the heating system as a separate zone, utilizing its own circulator pump.
Scanning QR Code In VS .NET
Using Barcode scanner for Visual Studio .NET Control to read, scan read, scan image in .NET applications.
Encoding Bar Code In .NET
Using Barcode creation for VS .NET Control to generate, create barcode image in .NET framework applications.
In hard-water areas, it is possible that even though the boiler is functioning properly, the domestic water does not get very hot. This is caused by a lime buildup on the heat exchanger, which acts as an insulator and inhibits the heat transfer. In this case, the coil is in need of a cleaning, although it may require replacement.
Decoding Bar Code In Visual Studio .NET
Using Barcode reader for VS .NET Control to read, scan read, scan image in VS .NET applications.
QR Code Creator In C#
Using Barcode generation for Visual Studio .NET Control to generate, create QR image in VS .NET applications.
Checkpoint summary
Painting Denso QR Bar Code In Visual Studio .NET
Using Barcode generation for ASP.NET Control to generate, create QR image in ASP.NET applications.
QR Code JIS X 0510 Generator In Visual Basic .NET
Using Barcode creation for .NET Control to generate, create QR Code image in VS .NET applications.
Is hot water supplied by a separate-tank type of water heater or by a tankless coil If you have a tank-type heater, record the capacity (gallons), the recovery rate (gallons per hour), and the age (from serial number). Are exhaust gases spilling out of the draft diverter Is tank-type heater adequate for house (See table.) Sum of tank capacity plus recovery rate
1D Creator In .NET
Using Barcode generator for .NET framework Control to generate, create 1D image in VS .NET applications.
Generate UPC Symbol In .NET
Using Barcode generation for VS .NET Control to generate, create UPC Code image in VS .NET applications.
70 90 105 115
Paint Code 128 Code Set C In .NET
Using Barcode printer for .NET framework Control to generate, create Code-128 image in .NET framework applications.
Printing ISBN - 13 In VS .NET
Using Barcode generation for .NET Control to generate, create ISBN - 13 image in VS .NET applications.
Fig. 16-10. Indirect-fired storage water heater. According to manufacturers, 15 20 gallons of domestic hot water is removed before the zone aquastat calls for hot water from the boiler. Consequently, with the high recovery rate, the boiler firings are kept to a minimum. In checking the unit, either raise the thermostat setting to HOT or let the hot water run until the boiler fires. You can tell if the pump is operating by touching the water supply to the heater before and after the boiler fires. The pipe should get hot. Look for signs of leakage around the base of the unit. Also, make sure that there is a pressure-temperature relief valve mounted directly on the tank casing. If you adjust the thermostat to activate the boiler and circulator pump, don t forget to reset it.
Print EAN / UCC - 13 In Objective-C
Using Barcode encoder for iPad Control to generate, create EAN 128 image in iPad applications.
Code 128 Code Set C Drawer In C#.NET
Using Barcode generation for VS .NET Control to generate, create Code 128 Code Set C image in .NET applications.
Full bathrooms
DataMatrix Maker In Visual Basic .NET
Using Barcode generation for Visual Studio .NET Control to generate, create Data Matrix 2d barcode image in Visual Studio .NET applications.
Print UPC Symbol In VB.NET
Using Barcode creator for .NET Control to generate, create UPC-A Supplement 5 image in .NET framework applications.
1 2 3 4
Generating Code 3 Of 9 In None
Using Barcode generation for Word Control to generate, create Code 3 of 9 image in Microsoft Word applications.
Barcode Encoder In None
Using Barcode drawer for Font Control to generate, create barcode image in Font applications.
Is hot-water flow adequate when two fixtures are turned on Are hot and cold supply lines incorrectly installed (reversed) Does water heater contain a properly installed temperature-pressure relief valve Is the relief valve dripping Look for signs of corrosion or past leakage: Tank type (gas-fired unit): corrosion dust and flaking metal in burner area. Tankless coil: rust and deposits around fittings and gasket. Is there an instant hot-water return line Ckeckpoint summary 229
Bar Code Maker In Java
Using Barcode drawer for BIRT reports Control to generate, create bar code image in BIRT applications.
DataMatrix Encoder In .NET Framework
Using Barcode encoder for Reporting Service Control to generate, create Data Matrix image in Reporting Service applications.
17 Air-conditioning
Air-conditioning capacity 231 Air-conditioning systems 232 Integral system 232 Split system 232 Inspection procedure 233 Heat pump 240 Evaporative cooler 241 Checkpoint summary 241
Before outlining the procedure for inspecting a central air-conditioning system, let me discuss the components of a typical residential system and their functions. Central air-conditioning systems provide comfort cooling by lowering the air temperature and removing excess moisture. This is achieved by recirculating air from the house across a cooling coil. As the air flows across the coil, its temperature drops, causing some of the moisture in the air to condense out on the coil. The cool, dehumidified air is then distributed throughout the house, and the moisture is disposed of through a drain. The basic components of an air-conditioning system are the compressor, condenser, expansion device, and evaporator. The evaporator is the cooling coil mentioned above. The other components simply provide the means for the evaporator coil to cool the circulating air. This is done using a cooling medium, a refrigerant, that cycles between the components. (See FIG. 17-1.) The refrigerant is normally a gas at atmospheric pressure and tempera230 Air conditioning
ture. By (1) applying pressure to the refrigerant and (2) removing absorbed heat, the refrigerant will change from a gas to a liquid. At this point, the refrigerant exists as a high-pressure liquid. When the pressure on the liquid refrigerant is released, the refrigerant (3) expands and changes back to a gas. In the process of changing from a liquid to a gas, the refrigerant (4) absorbs heat from its surroundings, thus cooling the air passing over the coil. An air-conditioning system is a closed system, and theoretically there should never be a need for additional refrigerant. However, in practice the various fittings on the connecting pipes can loosen or develop hairline cracks that can allow some of the refrigerant gas to escape. Usually, when a system is low in refrigerant, the practice is to introduce additional refrigerant and not to look for the openings in the system that allowed the refrigerant to escape. However, if the air-conditioning system cannot hold a refrigerant charge for at least one season, the leaks in the pipes or fittings should be located and corrected.
Copyright © OnBarcode.com . All rights reserved.