how to generate barcode in asp.net using c# Figure 23.1 Simple door lock. in .NET

Creation Denso QR Bar Code in .NET Figure 23.1 Simple door lock.

Figure 23.1 Simple door lock.
Decoding QR Code In .NET Framework
Using Barcode Control SDK for VS .NET Control to generate, create, read, scan barcode image in .NET framework applications.
QR Code Creator In .NET Framework
Using Barcode maker for .NET framework Control to generate, create QR Code 2d barcode image in VS .NET applications.
Making Locks by Hand
QR Code Recognizer In VS .NET
Using Barcode reader for Visual Studio .NET Control to read, scan read, scan image in .NET applications.
Bar Code Creation In VS .NET
Using Barcode encoder for .NET framework Control to generate, create barcode image in .NET framework applications.
Backplate Bolt Front Bolt Guide
Barcode Recognizer In .NET
Using Barcode decoder for VS .NET Control to read, scan read, scan image in Visual Studio .NET applications.
QR Code ISO/IEC18004 Generation In C#.NET
Using Barcode generation for .NET Control to generate, create QR Code ISO/IEC18004 image in .NET applications.
Mainspring & Keeper
QR Code Maker In Visual Studio .NET
Using Barcode printer for ASP.NET Control to generate, create Quick Response Code image in ASP.NET applications.
Encoding QR Code 2d Barcode In VB.NET
Using Barcode drawer for .NET Control to generate, create Quick Response Code image in .NET framework applications.
Rear Bolt Guide
Generate GS1 DataBar Expanded In Visual Studio .NET
Using Barcode creation for VS .NET Control to generate, create DataBar image in .NET framework applications.
Code 39 Printer In VS .NET
Using Barcode maker for VS .NET Control to generate, create Code 39 Full ASCII image in .NET framework applications.
Ward Plate Spacer (one of two) Coverplate Ward Plate Coverplate Spacer (one of two)
Painting 1D Barcode In .NET
Using Barcode maker for VS .NET Control to generate, create Linear 1D Barcode image in .NET framework applications.
Postnet 3 Of 5 Creation In VS .NET
Using Barcode generator for Visual Studio .NET Control to generate, create USPS POSTal Numeric Encoding Technique Barcode image in .NET applications.
Figure 23.2 Exploded view of door lock.
Encoding Barcode In None
Using Barcode generator for Microsoft Excel Control to generate, create barcode image in Office Excel applications.
Generating Data Matrix 2d Barcode In None
Using Barcode maker for Font Control to generate, create Data Matrix image in Font applications.
pivot hole as well as drilling a 1 4-inch hole near the base of the key bit. An engraving chisel with a 1 16-inch-wide cutting edge is used to remove material from one side of the keyhole. A regular cold chisel can then score the line on the opposite side of the keyhole (Fig. 23.6). The waste can then be broken away from the center of the keyhole. Clean up any rough edges with a file. 7. Rivet the front bolt guide in place. The rear bolt guide is fitted to the backplate but not riveted at this time. The bolt will need to be removed later to fit the mainspring and key.
Recognizing Bar Code In None
Using Barcode decoder for Software Control to read, scan read, scan image in Software applications.
Creating UCC - 12 In Java
Using Barcode generation for Java Control to generate, create GS1 - 12 image in Java applications.
Twenty-Three
Creating Barcode In Java
Using Barcode creator for Android Control to generate, create barcode image in Android applications.
Printing UPC Code In Objective-C
Using Barcode maker for iPad Control to generate, create GTIN - 12 image in iPad applications.
3 1/4"
Decoding Barcode In .NET Framework
Using Barcode recognizer for .NET framework Control to read, scan read, scan image in VS .NET applications.
Code 128 Code Set C Drawer In Visual Studio .NET
Using Barcode printer for Reporting Service Control to generate, create Code 128A image in Reporting Service applications.
Figure 23.3 The finished tail.
Figure 23.4 Transfer marks for the drill holes.
Hacksaw Tenons
Figure 23.5 After the bolt slides freely, cut out the tenons.
Making Locks by Hand
Drill Holes Provide Access For Engraving Chisel
Keyhole Outline On Backplate
Engraving Chisel Removes Metal Without Distorting Backplate
Drive Cold Chisel Along This Line To Remove Waste
Same Procedure Used On Lower Half Of Key
File Any Rough Edges
Figure 23.6 Make the keyhole by drilling and chiseling.
8. Insert several layers of paper or a thin cardboard between the bolt guide and the bolt before riveting the bolt guide to the backplate. This is the simplest way to make sure that there will be some play between the bolt guide and the bolt once the bolt guide is riveted in place. Burning away the paper once the riveting is done will release the bolt. 9. Cut out the coverplate and the ward plate from 16-gauge sheet metal. The coverplate and ward plate spacers are 13 4-inch lengths of 3 8-inch square bar. Grind the top edge of each spacer to conform to the top edge of the coverplate. Mark all pieces as shown in Fig. 23.7.
Twenty-Three
Mark All Pieces
Figure 23.7 Cut out and mark the
coverplate.
10. Center-punch the first rivet location on the top of spacer #1. Clamp spacer #1 to the ward plate. Drill a 3 16-inch hole through the spacer and ward plate. 11. Remove spacer #1 from the ward plate. Clean any burrs from the underside of the ward plate. Place spacer #2 under the ward plate. Use the rivet hole drilled in the ward plate to find the center punch location. Clamp spacer #2 to the ward plate and drill. 12. Remove spacer #2 from the ward plate. Place spacer #1 in position on top of the ward plate. Insert a rivet in the first drill hole to prevent the spacer from drifting out of position. Clamp in place, center-punch and drill the second rivet hole. 13. Remove spacer #1 from the ward plate. Place spacer #2 under the ward plate. Insert a rivet in the first drill hole. Clamp, center-punch, and drill. Repeat this procedure for spacers #3 and #4. 14. Assemble the ward plate and spacers by drilling a temporary rivet in each hole. Drill a 1 8-inch rivet hole in the center of each set of spacers. Counterbore the 1 8-inch hole from both sides and rivet the spacers in place. Make the 1 8-inch rivet from the shank of a common nail. Grind the rivet flush with the bottom of the ward plate and clean up all edges with a file. 15. The ward plate and spacers are used as a guide to drill the backplate and coverplate. A 3 8-inch bar is used to align the ward plate with the backplate or coverplate. Align the ward plate so that the 3 8-inch bar is perpendicular to backplate/coverplate. Clamp the ward plate in place and drill. As each hole is drilled, place a temporary rivet in the hole to keep the plate from drifting out of position. Do not rivet the ward plate to the coverplate or backplate at this time. 16. The mainspring is forged from a 6- to 8-inch piece of 5 16-inch square keystock. Forge one end of the bar into a thin, leaf shape as shown in Fig. 23.8.
Copyright © OnBarcode.com . All rights reserved.